Hilti
Baldor


Displaying: 1 - 24 of 158 Matching Items
158 Items
View:
Active Filters :
Part #:300786

10HP, 1770RPM, 3PH, 60HZ, 215T, 3752M, TEFC, F1
$ 1,436.54
Part #:301346

1HP, 1760RPM, 3PH, 60HZ, 56, 3520M, TEFC, F1, N
$ 708.42
Part #:302335

.33HP, 1140RPM, 1PH, 60HZ, 56, 3424L, TEFC, F1
$ 654.33
Part #:302577

.75HP, 1140RPM, 1PH, 60HZ, 56H, 3528LC, TEFC, F
$ 1,072.97
Part #:302892

1HP, 1760RPM, 3PH, 60HZ, 143T, 3520M, TEFC, F1
$ 708.42
Part #:302895

1.5HP, 1760RPM, 3PH, 60HZ, 145T, 3526M, TEFC, F
$ 787.22
Part #:302896

2HP, 1755RPM, 3PH, 60HZ, 145T, 3530M, TEFC, F1
$ 832.52
Part #:302901

3HP, 1760RPM, 3PH, 60HZ, 182T, 3632M, TEFC, F1
$ 854.17
Part #:302903

5HP, 1750RPM, 3PH, 60HZ, 184T, 3642M, TEFC, F1
$ 882.41
Part #:302905

5HP, 1750RPM, 3PH, 60HZ, 184TC, 3642M, TEFC, F1
$ 951.35
Part #:302910

15HP, 1765RPM, 3PH, 60HZ, 254T, 0944M, TEFC, F1
$ 2,213.24
Part #:302911

20HP, 1770RPM, 3PH, 60HZ, 256T, 0960M, TEFC, F1 Output20.000 hp Phase3 Synchronous Speed1,800 rpm Frequency60.00 Hz Voltage230 V460 V Frame MaterialIron Frame256T XP Class and GroupNONE XP DivisionNot Applicable BrandBaldor-Reliance Agency ApprovalsCSACSA EEVUR Ambient Temperature40 &degC Auxillary BoxNo Auxillary Box Auxillary Box Lead TerminationNone Base IndicatorRigid Bearing Grease TypePOLYREX EM (-20F +300F) BlowerNone Current52.0 A @ 208 V48.0 A @ 230 V24.0 A @ 460 V Design CodeA Drip CoverNo Drip Cover Duty RatingCONT Efficiency @ 100% Load93.0% Electrically Isolated BearingNot Electrically Isolated Feedback DeviceNo feedback Front Face CodeStandard Front Shaft IndicatorNone Heater IndicatorNo heater High Voltage Full Load Amps24.0 A Insulation ClassF Inverter CodeInverter ready KVA CodeJ Lifting LugsStandard Lifting Lugs Locked Bearing IndicatorLocked Bearing Motor Lead ExitKO Box Motor Lead Quantity/Wire Size9 @ 10 AWG Motor Lead TerminationFlying Leads Motor StandardsNEMA Motor Type0960M Number of Poles4 Overall Length23.28 in Power Factor83 Product FamilyGeneral Purpose Pulley End Bearing TypeBall Pulley Face CodeStandard Pulley Shaft IndicatorStandard Rodent ScreenNone Service Factor1.15 Shaft Diameter1.625 in Shaft Extension LocationPulley End Shaft Ground IndicatorNo Shaft Grounding Shaft RotationReversible Shaft Slinger IndicatorShaft Slinger Speed1,770 rpm Speed CodeSingle Speed Starting MethodDirect on line Thermal Device - BearingNONE (OLD) Thermal Device - WindingNone Vibration Sensor IndicatorNo Vibration Sensor Winding Thermal 1None Winding Thermal 2None
$ 2,683.32
Part #:303697

.75HP, 1750RPM, DC, 56C, 3528D, TEFC, F1
$ 1,594.76
Part #:303723

.75HP, 1725RPM, 3PH, 60HZ, 56C, 3420M, TEFC, F1
$ 426.10
Part #:511262

HDM Manual adhesive dispenser Manual dispenser HDM 500 + black cartr #3498241 Manual hybrid/epoxy adhesive anchor dispenser Dispenser typeManual
$ 292.49
Part #:511296

HIT-Z Anchor rod Anchor rod HIT-Z 5/8" x 9-1/2" #2018448Material, corrosionCarbon steel, zinc-platedWrench/nut size15/16 inDrill bit diameter3/4 inBase materialsConcrete (cracked), Concrete (uncracked)PROFIS SoftwareYesApprovals / Test reportsICC-ES report (concrete)Cleaning proceduresNon CleaningType of fixingPre-fastening, Through-fasteningProduct ClassUltimate
$ 122.54
BX
Part #:511332

HIT-RE 500 V3 Epoxy anchor Epoxy adh RE 500-V3 11.1oz/330ml #2123401 Base materialsConcrete (cracked), Concrete (uncracked)Base material conditionDry, Submerged, Water-filled, WetApprovals / Test reportsICC-ES report (concrete)Seismic loadingYesPROFIS SoftwareYesClean-TecNoCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air CleaningStorage and transportation temperature range41 - 77 &degFIn-service temperature &ndash range-40 - 158 &degFShelf life from date of manufacture (at 73&degF/23&degC and 50% relative humidity)12 monthsProduct informationThis product is subject to the Chemicals Prohibition Ordinance (ChemVerbotsV). It is to be used by professionals within the scope of their work and, in accordance with &sect 8 para. 3 no. 1 of the ChemVerbotsV, is to be used exclusively for its intended purpose as anchor adhesive, for rebar connections (typically steel-to-concrete and/or concrete-to-concrete connections), as well as for other intended fastening and uses within the scope of construction activities. Purchasers must comply with all existing legal requirements for the use of these products and may use them only as permitted. Information in the safety data sheets and operating instructions on the use of these products, the hazards associated with their use, the necessary safety measures during intended use and in the event of unforeseen spillage or release, and proper disposal must always be observed. The operating instructions and safety data sheets can be accessed in the detailed view of the products concerned at www.hilti.de in a format that can be saved and printed, and the operating instructions are enclosed with the products. Safety instructions Wear protective gloves/protective clothing/eye protection/face protection. Do not get in eyes, on skin or on clothing. In case of contact with eyes rinse thoroughly with water for several minutes. Remove contact lenses if possible, continue rinsing. If eye irritation, skin irritation or rash persist seek medical advice/attention. In case of contact with skin wash with plenty of soap and water. Disposal Completely emptied cartridges can be disposed of via the Dual System (yellow garbage can). Full/partially emptied containers are to be disposed of as special waste.Product ClassUltimate
$ 81.77
Part #:511731

HDM Manual adhesive dispenser Manual dispenser HDM 500 + red cartr #3498242 Manual hybrid/epoxy adhesive anchor dispenser Dispenser typeManual
$ 292.49
Part #:511733

Black cartridge HIT-CB 500 #2007057
$ 44.92
Part #:511740

Cartridge holder red HIT-CR 500 #2007059
$ 45.81
Part #:511331

HIT-HY 200-A V3 Adhesive anchor (New Verision) Ultimate-performance injectable hybrid mortar with approvals for anchoring structural steel baseplate and post-installed rebar connections Base materialsConcrete (cracked), Concrete (lightweight), Concrete (uncracked) Approvals / Test reportsDOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, Seismic PROFIS SoftwareYes Base materialsConcrete (cracked), Concrete (lightweight), Concrete (uncracked)Approvals / Test reportsDOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, SeismicPROFIS SoftwareYesClean-TecNoCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Non CleaningStorage and transportation temperature range41 - 77 &degFIn-service temperature &ndash range-40 - 248 &degFShelf life from date of manufacture (at 73&degF/23&degC and 50% relative humidity)12 monthsProduct ClassUltimate HIT-HY 200-A Adhesive anchor Hybrid adh HY 200-A 11.1oz/330ml #2022791 (Old Verision)Base materialsConcrete (cracked), Concrete (uncracked), Masonry (grout-filled CMU)Base material conditionDry, WetApprovals / Test reportsICC-ES report (concrete), SeismicSeismic loadingYesFatigue loadingNoFire resistanceNoPROFIS SoftwareYesClean-TecNoAnchoring elementsHAS threaded rods, HIS-N internally threaded sleeves, HIT-Z torque controlled bonded anchors, RebarCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Non CleaningStorage and transportation temperature range41 - 77 &degFIn-service temperature &ndash range-40 - 248 &degFShelf life from date of manufacture (at 73&degF/23&degC and 50% relative humidity)12 monthsProduct ClassUltimate
$ 64.39
Part #:511683

HIT-HY 200-R Adhesive anchor Hybrid adh HY 200-R 11.1oz/330ml #2022793 Replaced By HIT-HY 200-R V3 Adhesive anchor Ultimate-performance injectable hybrid mortar with approvals for post-installed rebar connections and anchoring structural steel baseplate Base materials Concrete (cracked), Concrete (lightweight), Concrete (uncracked) Approvals / Test reports DOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, Seismic PROFIS Software Yes
$ 64.39
Part #:500192

Kwik Bolt 1 carbon steel wedge anchor High-performance wedge anchor for cracked concrete and seismic (carbon steel) Material, corrosionCarbon steel, zinc-plated Head configurationExternally threaded Drilling Method (AS)Hammer Drilling, Hollow Drill Bit Drilling Material, corrosionCarbon steel, zinc-platedHead configurationExternally threadedDrilling Method (AS)Hammer Drilling, Hollow Drill Bit DrillingInstallation toolsTE 6-A36 Cordless rotary hammer, SIW 6AT-A22 Cordless impact wrench
$ 7.49
 
Displaying: 1 - 24 of 158 Matching Items