2in
Electrical Equipment
View:
Active Filters :
- Main Category: Electrical Equipment
- Size: 2in
- Electrical Boxes, Conduit, Strut, and Raceway: Electrical Fittings
Part #:303913
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$
23.10
Qty:
Part #:303962
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$
18.82
Qty:
Part #:304000
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$
12.02
Qty:
Part #:307124
- O-Z/Gedney threaded three piece couplings join two lengths of conduit when neither can be turned. Elbows provide a 90 change of direction in a conduit run. Gasket elbows also provide a compact wire pulling point.
$
68.17
Qty:
Part #:307977
- Appleton liquidtight STF Series connectors with threaded hubs are female ST Series connectors. They are designed to be used when making connection from liquidtight flexible metal conduit to threaded rigid conduit and IMC. The compact design results in a connector that offers a small turning radius.
$
65.24
Qty:
Part #:308003
- Appleton aluminum liquidtight ST Series connectors with plain throat provide a dependable connection for liquidtight flexible metal conduit. Their lightweight aluminum construction facilitates installation. The compact design results in a connector that offers a small turning radius. They seal out oil water dust dirt and fumes.
$
89.17
Qty:
Part #:300842
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$
3.65
Qty:
Part #:301405
- CANTEX 5133828 is a 2 in. x 90-Degree Plain End Schedule 40 Standard Radius Elbow used to change the direction of a conduit run by 90-Degree
Features
Schedule 40 Nonmetallic PVC construction for strength and durability
For indoor or outdoor use
Suitable for aboveground or buried
Plain-end connections are solvent weld
ETL listed Conforms to UL 651 and NEMA TC-3 Conforms to UL 651 and NEMA TC-3
Made in USA
$
2.09
Qty:
Part #:302393
- Appleton and O-Z/Gedney offer ETP 4000S Series steel EMT set screw connectors. They are used to ground and secure EMT raceways to boxes and enclosures. The 4000S Series have a male NPS threaded hub and are available with or without an insulated throat.
$
5.65
Qty:
Part #:302432
- Appleton HUB-B threaded conduit hubs with bonding screw are general purpose fittings designed for RMC and IMC. They provide threaded terminations in sheet metal enclosures and are suitable for service entrances.
$
35.27
Qty:
Part #:302675
- Appleton and O-Z/Gedney offer ETP 5000S Series steel EMT set screw couplings. They are used to ground and secure EMT raceway sections together.
$
6.19
Qty:
Part #:303756
- CANTEX 5133836 is a 2 in. x 90-Degree x 24 in. Radius Plain End Schedule 40 Special Radius Elbow used to change the direction of a conduit run by 90-Degree
Features
Schedule 40 Nonmetallic PVC construction for strength and durability
For indoor or outdoor use
Suitable for aboveground or buried
Plain-end connections are solvent weld
ETL listed Conforms to UL 651 and NEMA TC-3 Conforms to UL 651 and NEMA TC-3
Made in USA
$
22.99
Qty:
Part #:306953
- Appleton and O-Z/Gedney rigid conduit and IMC locknuts are used to secure and ground conduits and fittings to enclosures and prevents loosening due to vibration or motion. They are available in plain gasketed and bonding styles.
$
3.54
Qty:
Part #:306984
- Appleton and O-Z/Gedney conduit bushings are used with a locknut to terminate rigid metal conduit or IMC conduit to a box or enclosure. They provide a smooth pulling surface for wires.
$
3.20
Qty:
Part #:307381
- Appleton and O-Z/Gedney offer NEER ECO aluminum entrance caps. They are a clamp type aluminum entrance cap for threaded or unthreaded rigid conduit IMC or EMT service masts.
$
24.80
Qty:
Part #:308184
- O-Z/Gedney offers clamps and straps. They are used to secure oval/round cables or support runs of rigid metal conduit IMC and EMT.
$
1.43
Qty:
Part #:301342
- CANTEX 6141628 is a 2 in. Schedule 40 Standard Center Stop Coupling used to join lengths of conduit pipe together with two solvent weld socket ends
Features
For use with Schedule 40 and Schedule 80 conduit. May also be used in EB & DB Duct applications.
Center stop to help determine proper depth of connection
For use aboveground and underground and non-conductive and sunlight resistant
Meets NEMA TC-3 Standards
UL and CSA listed
Made in USA
$
0.82
Qty:
Part #:301367
- CANTEX 5140108 is a 2 in. Male Terminal Adapter which is a connector used to transition from a spigot end PVC conduit to a threaded metal or PVC plastic female bell end
Features
Durable non-conductive PVC will not rust or corrode
For use with Schedule 40 and Schedule 80 conduit. May also be used in EB & DB Duct applications.
Meets NEMA TC-3 Standards
UL and CSA listed
Made in USA
$
0.71
Qty:
$
18.84
Qty:
Part #:302737
- Appleton EY 25% fill vertical and horizontal conduit sealing fittings prevent the passage of gases vapors or flames from one portion of a conduit system to another. They also restrict large amounts of ignitable gases or vapors from accumulating to confine explosive pressure. Appleton sealing fittings are explosionproof dust-ignitionproof and raintight. They are suitable for use in Class I and II locations.
$
109.07
Qty:
Part #:304894
- Appleton and O-Z/Gedney threadless compression couplings are used to join lengths of rigid metal conduit. Threadless compression connectors are used to secure and terminate rigid metal conduit to enclosures. Threadless set-screw couplings are used to join lengths of rigid metal conduit and IMC. Threadless set-screw connectors are used to secure and terminate rigid metal conduit and IMC to enclosures.
$
63.01
Qty:
Displaying: 1 - 24 of 35 Matching Items