1-1/8"
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Alt. Size: 1-1/8"
Part #:500384
- 1-1/8" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:807747
- 3/4" Drive SAE 1-1/8" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
closeout
$23.00 MSRP
$
15.01
Part #:504774
- CLOSEOUTS Only 1 Left!
- 1/2" Drive 6-Point SAE 1-1/8" Shallow Socket &bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener &bull Designed for maximum engagement on 6 point fasteners
Qty:
Part #:511902
-
1-1/8" Anchor Shackle, Screw Pin, Forged Carbon Steel, Painted Blue
Shackle Bodies Are Drop-Forged Carbon Steel
Self Colored (Painted Blue)
C-419-S Shackles Meet the Design Requirements of Federal Specification RR-C-271, Type IVA, Grade A, Class 2
Working Load Limit, Size, Manufacture Name, Date Code and USA Permanently Marked on Each Shackle
Statistically Tested for Impact Resistance, Tensile Strength, Hardness, Ductility and Fatigue
419 Series Shackles Meet or Exceed All Manufacturing Requirements of the ASME B30.26 &rdquoRigging Hardware&rdquo. These Include the Material Ductility Requirement (Section 26-1.1.2), the Design Factor Requirement (Section 26.1.2), the Identification Requirement (Section 26-1.5.1), and the Effective Temperature Range (Section 26-1.6.1). the Shackles Can Be Proof Tested in Accordance with Section 26-1.4
Certification Available Upon Request
6 to 1 Design Factor
Pins and Bolts Are Heat-Treated and Made of Alloy Steel
Qty:
Part #:511854
-
1-1/8" Wire Rope Clip, Forged Carbon Steel, Galvanized
Base is Drop-Forged Carbon Steel
Hot Galvanized to ASTM A-153 to Resist Rust and Corrosion
U-Bolts Are colored Blue for Identification Purposes and Use Heavy Duty Hex Nuts (UNC-2A)
Designed to Meet Federal Specifications, FF-C-450, Type 1, Class 1
Designed to Meet or Exceed All Requirements of ASME B30.26 Including Identification, Ductility, Design Factor and Temperature
Permanently Marked with Size and Manufacturer
Sizes 1/4" and Above Marked with USA and Date Code
Sizes 1/8" Through 1-1/4" Are Supplied Bagged and Unassembled
Note See Application and Warning Information
Qty:
Part #:504373
- 1" Drive 6-Point SAE 1-1/8" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:507835
- 1/2" Drive SAE 1-1/8" Impact Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:812980
- 8" Cold Chisels 1 1/8"
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:500465
- 1/2" Drive 12-Point SAE 1-1/8" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:500483
- 1/2" Drive 12-Point SAE 1-1/8" Deep Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:500491
- 3/4" Drive Shallow Sockets, 12-Point, SAE, High Polished Chrome Finish
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:805885
- 1/2" Drive 6-Point SAE 1-1/8" Deep Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
Qty:
Part #:509572
- 1-1/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:509575
- 1-1/8" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:729-49-59-2113
- 1-1/8" x 2" Annular Cutter
Dual alternating tooth geometry and thin-wall construction help Milwaukee&rsquos Annular Cutter cut up to 15% faster than the competition. With 20% thinner walls, the cutter displaces less material for the same size hole, giving you fast, burr-free holes in anything from sheet metal to thick steel plate.Milwaukee&rsquos proprietary high-speed steel with three hardness zones minimizes breakage and helps the bit last longer. It comes with a 3/4&rdquo Weldon shank, which is ideal for use with most small magnetic drill presses and large magnetic drill presses with the correct arbor.
Qty:
Part #:729-48-20-7256
- 1-1/8" Bit,18" Bit,SDS+,TE-CX,4-Cutter,:
Qty:
Part #:729-49-56-0052
- 1-1/8" Hole Dozer&trade Bi-Metal Hole Saw
Made in the USA, the Milwaukee®HOLE DOZER&trade Hole Saw features Rip Guard&trade, the strongest tooth form in the industry, backed by the Rip Guard&trade Limited Lifetime Tooth Break Warranty. Each tooth is built with more steel behind the cutting edge for added strength. The Rip Guard&trade warranty on tooth breaks is a first for the hole saw industry. The added tooth strength along with 8% cobalt give added life to the teeth, allowing for increased productivity on the jobsite, as well as continued hole quality. The HOLE DOZER&trade includes Plug Jack&trade, an all access slot design that allows for full access during plug removal. The Plug Jack&trade gives access lower into the cup for thick material and higher towards the teeth for thin material. With multiple positions to apply leverage and better plug access, Plug Jack&trade increases productivity and eliminates wasted downtime between holes. For fast, tool-free change-outs, use Milwaukee's universal Quick-Change Arbor. 49-56-7240, 49-56-7250, and 49-56-9100
Qty:
Part #:729-2715-22
- M18 FUEL&trade 1-1/8" SDS Plus Rotary Hammer Kit (Discontinued, Replaced by 2915-20)
Powered by FUEL&trade technology, the M18 FUELTM 1-1/8&rdquo SDS Plus Rotary Hammer delivers faster than corded speed, corded durability, and all day work on one charge. The Milwaukee POWERSTATE&trade Brushless Motor Provides 3.3 ft-lbs of impact energy, 0-1,350 RPM, and 0-5,000 BPM. The Milwaukee REDLITHIUM&trade XC5.0 Battery Packs provide all day work on one charge, 20% more power, and 2X more life than standard Lithium-Ion batteries. REDLINK PLUS&trade Intelligence integrates full-circle communication between tool, battery, and charger to protect from overloading, overheating, and over-discharging.
Qty:
Part #:507217
- COO China:
Qty:
Part #:1184-JHW14-636
- 1/2" Drive SAE 1-1/8" Impact Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Displaying: 1 - 20 of 20 Matching Items