10"
3" x 3" x 1-1/2"
View:
Active Filters :
- Alt. Size: 3" x 3" x 1-1/2" 10"
closeout
$12,905.02 MSRP
$
2,530.00
Qty:
Part #:811717
- 10" Combination Slip Joint Pliers
&bull Multiple parallel jaw positions are locked in to proper groove for superior non-slip performance
&bull Serrated jaws for maximum gripping power
&bull Polished heads resist rust and corrosion, extending the tool life
&bull Shear type wire cutter extends tool use
Qty:
Part #:500541
- 1/2" Drive 10" Extension
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
&bull Spinner disk is ideal for fast turn down of fasteners
Qty:
$
48.12
Qty:
Smith Blair Service Saddle Double Bale 10in - 12in x 3/4in CC 10.64in-12.12in Range 313-00121207-000
- 313 Service Saddle, Double Bale - For tapping branch connections on new or existing pipe, installing line appurtenances
Description Double bale Ductile Iron service saddle with TaperSeal&trade gasket and wraparound bales toconnect branch lines, instruments, and other appurtenances to pipe.Application Tapping pipe for branch connections and to install service connections, air and vacuum valves.Key Features
&bullMeets applicable AWWA C800 Standards
&bullThe wide saddle body provides stability on the pipe
&bullThe gasket is fully bonded to the cavity to hold it in place
&bullNPT, CC and other threaded outlets available in sizes " thru 4"&bullA closed lug on one side, combined with the bale, acts as a hinge for easier installation
$
108.96
Qty:
$
46.17
Qty:
Part #:811827
- 1/2" Drive Impact Extensions
Overview
&bull Specially heat treated for impact use to provide long life, safety, and durability
&bull Spring plunger provides secure socket retention for safety and convenience
&bull Suitable for use with pneumatic and electric impact wrenches
Qty:
Qty:
closeout
$277.65 MSRP
$
172.42
Part #:810316
- CLOSEOUTS Only 1 Left!
- Copper Plated Screw C-Clamp Capacity 10" &bull Copper plated screw resists weld splatter &bull Drop-forged and heat treated for maximum strength and greater rigidity &bull I-Beam design for extra strength &bull Highly resistant to &rdquospringing&rdquo
Qty:
Part #:203867
- Socket Clamps Pipe OD 11.10in, 5/8in-11 x 3in Bolt Size, Stock Size 1/2in x 2in,
For use in preventing underground pipe joints from separating
Also known as &ldquoRetainer Clamps&rdquo or &ldquoFriction Clamps&rdquo. Designed for centrifugally-spun cast and ductile iron pipe with OD&rsquos as shown in the table below.
All Socket Clamps include two half clamps, two bolts and nuts and two washers. Sizes 3&Prime through 12&Prime are supplied with #585 cast washers, which are shown below as replacement parts. Sizes 14&Prime and larger are supplied with two fabricated washers.
Used with all-thread rod and Trumbull tie-lugs or tie-bolts for joint restraint, shown
Qty:
Part #:501-D25985
- DS Series In-Line Condensate SeparatorsCarbon Steel Drain SeparatorCondensate in steam and air piping reduces thermal efficiency, causes water hammer, corrodes equipment such as valves and pipes, and causes other problems.
In-line (drain) separators DS-1, DS-2, DS-3, and DS-4 separate condensate efficiently by using the centrifugal force of steam or air created by introducing it into a specifically shaped path. Because of the simple structure of the drain separators, pressure loss is minimized, enabling clean, dry steam or air to be fed to equipment.
When steam or air flow enters the drain separator, centrifugal force is generated in the fluid because of the devices internal structural design. The fluid drains along the wall because of the difference in specific gravity with steam or air, eventually striking the baffle. The baffle guides the fluid to the drain outlet and to the trap, which drains it. As a result, small dirt particles and condensate are separated and removed from the system through the bottom drain.
• Cyclone structure maximizes liquid separation efficiency
• Pressure loss is extremely low
• No moving parts means no breakdowns
Qty:
Part #:501-D25986
- DS Series In-Line Condensate SeparatorsCarbon Steel Drain SeparatorCondensate in steam and air piping reduces thermal efficiency, causes water hammer, corrodes equipment such as valves and pipes, and causes other problems.
In-line (drain) separators DS-1, DS-2, DS-3, and DS-4 separate condensate efficiently by using the centrifugal force of steam or air created by introducing it into a specifically shaped path. Because of the simple structure of the drain separators, pressure loss is minimized, enabling clean, dry steam or air to be fed to equipment.
When steam or air flow enters the drain separator, centrifugal force is generated in the fluid because of the devices internal structural design. The fluid drains along the wall because of the difference in specific gravity with steam or air, eventually striking the baffle. The baffle guides the fluid to the drain outlet and to the trap, which drains it. As a result, small dirt particles and condensate are separated and removed from the system through the bottom drain.
• Cyclone structure maximizes liquid separation efficiency
• Pressure loss is extremely low
• No moving parts means no breakdowns
Qty:
Part #:501-D27092
- AEH Series Exhaust Heads Armstrongs AEH series carbon steel exhaust heads should be used when there is a risk of water carryover up an atmospheric vent pipe. The internal knock-out plate and stainless steel mesh screening effectively contains water carry-over and discharges it through the bottom drain leaving dry flash steam to vent through the top of the vessel.
Connections
• Flanged ASME B16.5 CL 150
• Drain FNPT
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:511-BYV11100A0VG000
Qty:
Part #:511-BYV11100A0VGI00
Qty:
Qty:
Qty:
Part #:785-1410741
- Shielded Rubber Coupling 10" Culvert Coupling ADS/Hancor/JM Eagle x 10" Culvert Coupling ADS/Hancor/JM Eagle
$
325.41
Qty:
Qty:
Qty:
Displaying: 49 - 72 of 73 Matching Items