Bottom Inlet Air Vents
Steam and Filter Products


Displaying: 1 - 24 of 224 Matching Items
224 Items
View:
Active Filters :
Part #:501-C3510-1
1-AV Series Air and Gas VentsFor pressures to 300 psig (21 bar) or specific gravity down to 0.40. 1-AVA cast iron air vent that uses a free-floating lever that closes positively, ensuring a leaktight closing under all conditions. This vent is good for low capacity air/gas venting up to 300 psi (21 bar).
$287.00 MSRP $ 250.06
Qty:
add to cart
Part #:501-C3510-12
1-AV Series Air and Gas VentsFor pressures to 300 psig (21 bar) or specific gravity down to 0.40. 1-AVA cast iron air vent that uses a free-floating lever that closes positively, ensuring a leaktight closing under all conditions. This vent is good for low capacity air/gas venting up to 300 psi (21 bar).
$287.00 MSRP $ 251.06
Qty:
add to cart
Part #:501-C3510-2
1-AV Series Air and Gas VentsFor pressures to 300 psig (21 bar) or specific gravity down to 0.40. 1-AVA cast iron air vent that uses a free-floating lever that closes positively, ensuring a leaktight closing under all conditions. This vent is good for low capacity air/gas venting up to 300 psi (21 bar).
$287.00 MSRP $ 243.50
Qty:
add to cart
Part #:501-C5490
Thermostatic Air Vents Armstrong offers thermostatic air vents for positive venting of air and other non-condensable gases from steam in chamber-type heat-transfer equipment. Typical applications include jacketed kettles, retorts, vulcanizers, jacketed sterilizers or other contained equipment where air could accumulate in remote areas of the steam chamber and reduce heat-transfer capacity. These vents are balanced-pressure air vents that respond to the pressure-temperature curve of steam. Air is automatically vented at slightly below steam temperature throughout the entire operating pressure range.
$798.00 MSRP $ 679.19
Qty:
add to cart
Part #:501-C5491
Thermostatic Air Vents Armstrong offers thermostatic air vents for positive venting of air and other non-condensable gases from steam in chamber-type heat-transfer equipment. Typical applications include jacketed kettles, retorts, vulcanizers, jacketed sterilizers or other contained equipment where air could accumulate in remote areas of the steam chamber and reduce heat-transfer capacity. These vents are balanced-pressure air vents that respond to the pressure-temperature curve of steam. Air is automatically vented at slightly below steam temperature throughout the entire operating pressure range.
$889.00 MSRP $ 759.61
Qty:
add to cart
Part #:501-D27087
AEH Series Exhaust Heads Armstrongs AEH series carbon steel exhaust heads should be used when there is a risk of water carryover up an atmospheric vent pipe. The internal knock-out plate and stainless steel mesh screening effectively contains water carry-over and discharges it through the bottom drain leaving dry flash steam to vent through the top of the vessel. Connections &#8226 Flanged ASME B16.5 CL 150 &#8226 Drain FNPT
$1,023.00 MSRP $ 874.79
Qty:
add to cart
Part #:501-D27088
AEH Series Exhaust Heads Armstrongs AEH series carbon steel exhaust heads should be used when there is a risk of water carryover up an atmospheric vent pipe. The internal knock-out plate and stainless steel mesh screening effectively contains water carry-over and discharges it through the bottom drain leaving dry flash steam to vent through the top of the vessel. Connections &#8226 Flanged ASME B16.5 CL 150 &#8226 Drain FNPT
$1,922.00 MSRP $ 1,629.12
Qty:
add to cart
Part #:501-D27089
AEH Series Exhaust Heads Armstrongs AEH series carbon steel exhaust heads should be used when there is a risk of water carryover up an atmospheric vent pipe. The internal knock-out plate and stainless steel mesh screening effectively contains water carry-over and discharges it through the bottom drain leaving dry flash steam to vent through the top of the vessel. Connections &#8226 Flanged ASME B16.5 CL 150 &#8226 Drain FNPT
$3,004.00 MSRP $ 2,546.25
Qty:
add to cart
Part #:501-D27090
AEH Series Exhaust Heads Armstrongs AEH series carbon steel exhaust heads should be used when there is a risk of water carryover up an atmospheric vent pipe. The internal knock-out plate and stainless steel mesh screening effectively contains water carry-over and discharges it through the bottom drain leaving dry flash steam to vent through the top of the vessel. Connections &#8226 Flanged ASME B16.5 CL 150 &#8226 Drain FNPT
$4,205.00 MSRP $ 3,564.23
Qty:
add to cart
Part #:501-D27091
AEH Series Exhaust Heads Armstrongs AEH series carbon steel exhaust heads should be used when there is a risk of water carryover up an atmospheric vent pipe. The internal knock-out plate and stainless steel mesh screening effectively contains water carry-over and discharges it through the bottom drain leaving dry flash steam to vent through the top of the vessel. Connections &#8226 Flanged ASME B16.5 CL 150 &#8226 Drain FNPT
$5,404.00 MSRP $ 4,580.49
Qty:
add to cart
Part #:501-D27092
AEH Series Exhaust Heads Armstrongs AEH series carbon steel exhaust heads should be used when there is a risk of water carryover up an atmospheric vent pipe. The internal knock-out plate and stainless steel mesh screening effectively contains water carry-over and discharges it through the bottom drain leaving dry flash steam to vent through the top of the vessel. Connections &#8226 Flanged ASME B16.5 CL 150 &#8226 Drain FNPT
$7,279.00 MSRP $ 6,169.81
Qty:
add to cart
 
Displaying: 1 - 24 of 224 Matching Items