Anchor
3M
View:
Active Filters :
Qty:
Qty:
Qty:
Part #:508996
- Proto 3/4" Drive Deep Impact Socket 1-1/2" 6 Point
Proto® 6 Point Impact Sockets are ideal for use on stubborn or damaged fasteners, and also on fasteners made from soft materials.
The TorquePlus&trade design is a high performance drive configuration which allows for quick and easy socket engagement to the fastener flats, not the corners.
The TorquePlus&trade configuration employs a radius-corner design, shifting contact area and stress away from the fastener corners and distributing contact stresses over a large area of the socket, minimizing slippage.
The TorquePlus&trade internal design minimizes fastener rounding, helps to extend fastener life, and allows the user to more easily turn worn, rounded, or rusted fasteners.
Stamped size for easy reference.
Side locking hole.
Qty:
Qty:
Qty:
Part #:810356
- 1" Drive 12-Point SAE 1-1/2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:810222
- 1/2" Drive SAE 5/8" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Qty:
Qty:
Part #:503703
- 5/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:134-J86058
- Made from S2 steel and specially heat-treated for greater strength and durability.
Hand-ground cutting edge to the exact angle for cutting through tough metals.
20% larger striking surface than standard chisels directs the power to the cutting edge.
Longer shank features a knurl for better grip and easy positioning.
Black oxide finish to help prevent rust corrosion extending tool life and performance.
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:713136
-
Category Gates, Globes & Checks
Subcategory
Bronze
Series Type
Check Valve
Model No.
CVB
Threaded, Bronze In-Line Ball Cone Check Valve, Size 1/4" to 3" (DN 8 to DN 75)
Qty:
Qty:
Part #:501956
- 6 1/2" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Qty:
Part #:134-J5448H
- Proto® 6 Point Sockets are ideal for use on stubborn or damaged fasteners, and also on fasteners made from soft materials.
The TorquePlus&trade design is a high performance drive configuration which allows for quick and easy socket engagement to the fastener flats, not the corners.
The TorquePlus&trade configuration employs a radius-corner design, shifting contact area and stress away from the fastener corners and distributing contact stresses over a large area of the socket, minimizing slippage.
The TorquePlus&trade internal design minimizes fastener rounding, helps to extend fastener life, and allows the user to more easily turn worn, rounded, or rusted fasteners.
Qty:
Displaying: 1 - 24 of 79 Matching Items