Anchor
3M
View:
Active Filters :
- Brand: 3M Anchor Apollo Cleveland Twist/Greenfield Fluke Hoffman/nVent J.H. Williams Lithonia Rust-Oleum Smith-Blair Inc Southwire
- Alt. Size: 1/2" 1/8" 8"
Qty:
Qty:
Qty:
Part #:701690
- Ball Valves
Subcategory
Brass & Bronze
Series Type
2 (Two) Piece
Threaded, 2-Piece, Std. Port, Bronze Ball Valve, 600 CWP, Sizes 1/4" to 4" (DN 8 to DN 100)
Qty:
Part #:704245
- Threaded, Unibody, Reduced Port, Stainless Steel Ball Valve, 2000 CWP to 1", 1500 CWP to 2", Sizes 1/4" to 2" (DN 8 to DN 50)
Qty:
Part #:709561
- Category Ball Valves
Subcategory
Brass & Bronze
Series Type
2 (Two) Piece
Lead-Free NPT Bronze Ball Valve, 600 CWP, Sizes 1/4" to 4".
Qty:
Part #:500550
- 3/4" Drive Extensions
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
Qty:
Part #:500695
- 1/2" Drive SAE 1/2" Long Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810245
- 6" Cold Chisels 1/2"
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:503702
- 1/2" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:700601
- Category
Ball Valves
Subcategory
Brass & Bronze
Series Type
3 (Three) Way
Threaded, Three-Way, Std. Port, Bronze Ball Valve,400 CWP, Sizes 1/4" to 2" (DN 8 to DN 50)
Qty:
Part #:702270
-
Category
Ball Valves
Subcategory
Brass & Bronze
Series Type
2 (Two) Piece
Threaded, 2-Piece, Std. Port, Bronze Ball Valve, w/Spring-Return Handle, 600 CWP, Sizes 1/4" to 2" (DN 8 to DN 50)
Qty:
Part #:810220
- 1/2" Drive SAE 1/2" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:204821
- 226 Full Circle Clamp DI Lug Single Band - For repairing complete breaks, splits, holes in pipe or joining pipe
Description These clamps provide fast, economical means for repairing full circumferential breaks,holes, cracks and other types of damage.Application Works on Cast Iron, Ductile Iron, Steel, Asbestos Cement, Copper, Aluminum, PVC, HDPE,Fiberglass and other pipe types.Key Features
&bullStainless Steel bands&bullWorking pressure up to 300 PSI
&bullNominal temperature range -20°F to 180°F
&bullRemovable lugs to allow installation in tight spaces
&bullMay be used to join plain end pipe of the same diameter
&bullStandard widths through 30"
&bull360° gasket seal&bullFlexi-Coat® Epoxy Finish for corrosion resistance
&bullRange up to .40" in single band
&bullDrop-in bolts for easier installation
$
270.62
Qty:
Part #:204364
- 226 Full Circle Clamp DI Lug Single Band - For repairing complete breaks, splits, holes in pipe or joining pipe
Description These clamps provide fast, economical means for repairing full circumferential breaks,holes, cracks and other types of damage.Application Works on Cast Iron, Ductile Iron, Steel, Asbestos Cement, Copper, Aluminum, PVC, HDPE,Fiberglass and other pipe types.Key Features
&bullStainless Steel bands&bullWorking pressure up to 300 PSI
&bullNominal temperature range -20°F to 180°F
&bullRemovable lugs to allow installation in tight spaces
&bullMay be used to join plain end pipe of the same diameter
&bullStandard widths through 30"
&bull360° gasket seal&bullFlexi-Coat® Epoxy Finish for corrosion resistance
&bullRange up to .40" in single band
&bullDrop-in bolts for easier installation
$
395.67
Qty:
Part #:203071
- 313 Service Saddle, Double Bale - For tapping branch connections on new or existing pipe, installing line appurtenances
Description Double bale Ductile Iron service saddle with TaperSeal&trade gasket and wraparound bales toconnect branch lines, instruments, and other appurtenances to pipe.Application Tapping pipe for branch connections and to install service connections, air and vacuum valves.Key Features
&bullMeets applicable AWWA C800 Standards
&bullThe wide saddle body provides stability on the pipe
&bullThe gasket is fully bonded to the cavity to hold it in place
&bullNPT, CC and other threaded outlets available in sizes " thru 4"&bullA closed lug on one side, combined with the bale, acts as a hinge for easier installation
$
84.30
Qty:
Part #:203072
- 313 Service Saddle, Double Bale - For tapping branch connections on new or existing pipe, installing line appurtenances
Description Double bale Ductile Iron service saddle with TaperSeal&trade gasket and wraparound bales toconnect branch lines, instruments, and other appurtenances to pipe.Application Tapping pipe for branch connections and to install service connections, air and vacuum valves.Key Features
&bullMeets applicable AWWA C800 Standards
&bullThe wide saddle body provides stability on the pipe
&bullThe gasket is fully bonded to the cavity to hold it in place
&bullNPT, CC and other threaded outlets available in sizes " thru 4"&bullA closed lug on one side, combined with the bale, acts as a hinge for easier installation
$
84.30
Qty:
Part #:810266
- 4 3/4" Pin Punches
For driving out and removing already loosened pins and keys after initial movement by a solid or starter punch
Qty:
Part #:203087
- 411 Steel Coupling, Straight - For joining plain-end pipe of same outside diameters
Description A bolted sleeve type coupling for joining plain end pipe of the same diameters.Application Joining plain end pipe without the need for welding or special pipe fittings.Key Features
&bullMeets applicable AWWA C219 Standards
&bullAllows for limited expansion and contraction
&bullWill dampen vibration to reduce pipe fatigue
&bullEasy to install, no special pipe end preparation required&bullAvailable in a wide variety of pipe O.D. sizes and sleeve lengths
&bullMost sizes will accommodate anchor studs to restrain the joints
&bullCan be custom made to fit odd O.D.s or other unusual applications
&bullProvided with or without pipe stops to accommodate customer needs
&bullHas good deflection capabilities, allows change in piping direction without the need of elbows, bends
&bullSteel sizes built to specific O.D. and Ductile Iron sizes are built with range to accommodate the variances inDuctile Iron pipe O.D.s
$
49.47
Qty:
Part #:810314
- 6" Center Punches
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
Displaying: 1 - 24 of 92 Matching Items