A.Y. Mcdonald Water Works
Aerokroil
View:
Active Filters :
Qty:
Qty:
Part #:508066
- Proto 1/2" Drive Hex Bit Impact Socket 3/8"
Features and Benefits
Proto® Hex Bit Impact Sockets can be used on stubborn fasteners.
Tight tolerances for snug fit on fastener.
Hex bit impact sockets are used wherever powered drive tools are used to install or remove fasteners.
Hex bit impact sockets are designed to withstand the high torque and force associated with impact tools in repetitive application.
Side locking hole.
Qty:
Part #:810217
- 1/2" Drive SAE 3/8" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:503700
- 3/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:503686
- 3/8" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:204515
- 441 OMNI Cast Coupling - For joining plain-end pipe of same outside diameters or outside diameters within same nominal pipe size
Description Cast CouplingsApplication To join plain end pipes with the same or different O.D.s by changing followers and gaskets.Key Features&bull Heavy cast Ductile Iron parts for long life&bull Meets applicable AWWA C219 Standards&bull Flanges and gaskets can be mixed and matched on the same size nominal sleeve&bull Most couplings are stab fit, making installation a b eeze. No disassembly is required&bull Up to 2.4" of range with a single coupling, reducing the need for large coupling inventories&bull One sleeve per nominal pipe size takes the guess work out of deciding which sleeve size to choose&bull Flanges are color coded by pipe type Red for iron pipe size O.D. Blue for Ductile O.D. and gray forAsbestos Cement O.D.&bull Gaskets and flanges a e permanently marked with a part number and range to facilitate proper selection&bull Sleeves are available in a variety of lengths, and custom length Steel sleeves are available for special applications
$
364.65
Qty:
Part #:200227
- 441 OMNI Cast Coupling - For joining plain-end pipe of same outside diameters or outside diameters within same nominal pipe size
Description Cast CouplingsApplication To join plain end pipes with the same or different O.D.s by changing followers and gaskets.Key Features&bull Heavy cast Ductile Iron parts for long life&bull Meets applicable AWWA C219 Standards&bull Flanges and gaskets can be mixed and matched on the same size nominal sleeve&bull Most couplings are stab fit, making installation a b eeze. No disassembly is required&bull Up to 2.4" of range with a single coupling, reducing the need for large coupling inventories&bull One sleeve per nominal pipe size takes the guess work out of deciding which sleeve size to choose&bull Flanges are color coded by pipe type Red for iron pipe size O.D. Blue for Ductile O.D. and gray forAsbestos Cement O.D.&bull Gaskets and flanges a e permanently marked with a part number and range to facilitate proper selection&bull Sleeves are available in a variety of lengths, and custom length Steel sleeves are available for special applications
$
364.65
Qty:
Qty:
Qty:
Qty:
Part #:810243
- 5 1/2" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:810313
- 5" Center Punches
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
Qty:
Part #:500372
- 3/8" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:501575
- 3/4" Drive 12-Point SAE 2-3/16" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Qty:
Qty:
Qty:
Qty:
Displaying: 1 - 24 of 77 Matching Items