Apollo
Aerokroil
View:
Active Filters :
- Brand: Aerokroil Apollo Bell and Gossett J. H. Williams Jamesbury J.H. Williams Ocal Powers Fastening Inc Proto Rust-Oleum
- Alt. Size: 1/2" 1/8" 10"
Part #:700026
- 1/2in Jamesbury 3000 Series Fire-Tite Threaded Ball Valve. Carbon steel body with stainless steel ball. Filled PTFE seats with graphite seal. Jamesbury Part # MA0012404332236MLC
Qty:
Part #:700045
- 1/2in Jamesbury 3000 Series Fire-Tite Threaded Stainless Steel Ball Valve. Stainless steel body with stainless steel ball and stem. Filled PTFE seats with graphite seal. Jamesbury Part # MA0012408333600MLC
Qty:
Part #:701690
- Ball Valves
Subcategory
Brass & Bronze
Series Type
2 (Two) Piece
Threaded, 2-Piece, Std. Port, Bronze Ball Valve, 600 CWP, Sizes 1/4" to 4" (DN 8 to DN 100)
Qty:
Part #:704245
- Threaded, Unibody, Reduced Port, Stainless Steel Ball Valve, 2000 CWP to 1", 1500 CWP to 2", Sizes 1/4" to 2" (DN 8 to DN 50)
Qty:
Part #:706812
- Unique Sealing The superior performance of Jamesbury ball valves is achieved by the unique design of the seats. The flexible lip seats exert continuous sealing pressure on the ball and automatically compensate for wear and changes in pressure and temperature, yielding positive bi-directional zero-leak shut-off. The stem seal sealing system ensures minimum emissions. Materials Standard products are available with carbon steel body and stainless steel trim or all stainless steel construction. Special body and trim materials such as Alloy 20, Hastelloy® C, and others are available upon request. For applications involving chemicals, acids, caustics, and steam we recommend our Xtreme® seat material, which provides superior lifecycle and sealing performance compared to virgin or filled PTFE. We can accommodate nearly any special customer or application specific requirement. Fite-Tite® Valves All Jamesbury Fire-Tite flanged ball valves are qualified to API 607 and ISO 10497. This ensures minimal leakage in the event of a fire.:
Qty:
Part #:709561
- Category Ball Valves
Subcategory
Brass & Bronze
Series Type
2 (Two) Piece
Lead-Free NPT Bronze Ball Valve, 600 CWP, Sizes 1/4" to 4".
Qty:
Part #:710080
- Unique Sealing The superior performance of Jamesbury ball valves is achieved by the unique design of the seats. The flexible lip seats exert continuous sealing pressure on the ball and automatically compensate for wear and changes in pressure and temperature, yielding positive bi-directional zero-leak shut-off. The stem seal sealing system ensures minimum emissions. Materials Standard products are available with carbon steel body and stainless steel trim or all stainless steel construction. Special body and trim materials such as Alloy 20, Hastelloy® C, and others are available upon request. For applications involving chemicals, acids, caustics, and steam we recommend our Xtreme® seat material, which provides superior lifecycle and sealing performance compared to virgin or filled PTFE. We can accommodate nearly any special customer or application specific requirement. Fite-Tite® Valves All Jamesbury Fire-Tite flanged ball valves are qualified to API 607 and ISO 10497. This ensures minimal leakage in the event of a fire.:
Qty:
Part #:500695
- 1/2" Drive SAE 1/2" Long Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810245
- 6" Cold Chisels 1/2"
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:503702
- 1/2" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:700601
- Category
Ball Valves
Subcategory
Brass & Bronze
Series Type
3 (Three) Way
Threaded, Three-Way, Std. Port, Bronze Ball Valve,400 CWP, Sizes 1/4" to 2" (DN 8 to DN 50)
Qty:
Part #:702270
-
Category
Ball Valves
Subcategory
Brass & Bronze
Series Type
2 (Two) Piece
Threaded, 2-Piece, Std. Port, Bronze Ball Valve, w/Spring-Return Handle, 600 CWP, Sizes 1/4" to 2" (DN 8 to DN 50)
Qty:
Part #:810220
- 1/2" Drive SAE 1/2" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810266
- 4 3/4" Pin Punches
For driving out and removing already loosened pins and keys after initial movement by a solid or starter punch
Qty:
Part #:810314
- 6" Center Punches
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
closeout
Part #:519024
- CLOSEOUTS Only 128 Left!
- The Polly is a sleeve type hollow wall anchor designed for use in base materials such as plaster, wallboard, concrete block or hollow tile. Once the anchor has been set, the screw may be removed as often as necessary without affecting the anchor. Allows for fixture and screw removal and re-anchoring.
$
0.26
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:519023
- Country of Origin TW:
Qty:
Part #:519033
- Country of Origin VN:
Qty:
Part #:1184-JHWISFXT616
- 3/8" Drive 6-Point SAE 1/2" 6.57"/116.9mm Shank Length Tension Socket Flextension
Made in the U.S.A
Durable black oxide finish
Socket retention pin is TIG welded, providing full rotation power to the socket
Sockets feature SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Drive end has a 7/32" cross hole & bevel for ease of use
Up to 30 degree angle offset
Flextensions are designed for use on hand and power tools (Impulse or Direct drive) NOT FOR IMPACT TOOL USE
Maximum working torque values 160 Ft. Lbs. /1920 In. Lbs. /217 Nm
Other lengths and socket sizes available by special order. Contact your Snap-on Industrial Brands representative
Qty:
Qty:
Displaying: 1 - 24 of 73 Matching Items