Apollo
Aerokroil
View:
Active Filters :
Part #:700031
- 3/4in Jamesbury 3000 Series Fire-Tite Threaded Ball Valve. Carbon steel body with stainless steel ball. PTFE seats with graphite seal. Jamesbury Part # MA0015380332236MLC
Qty:
Part #:700067
- 3/4in Jamesbury 3000 Series Fire-Tite Threaded Stainless Steel Ball Valve. Stainless steel body with stainless steel ball and stem. Filled PTFE seats with graphite seal. Jamesbury Part # MA0015383333600MLC
Qty:
Part #:513170
- Country of Origin CN:
Qty:
Part #:503704
- 3/4" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:710016
-
Category
Ball Valves
Subcategory
Carbon Steel
Series Type
2 (Two) Piece
Threaded, 2-Piece, Std. Port, Forged Carbon Steel Ball Valve, 2000 CWP to 1", 1500 CWP to 2", Sizes 1/4" to 2" (DN 8 to DN 50)
Qty:
Part #:503692
- 3/4" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:521096
- Country of Origin TW:
Qty:
Part #:521097
- Country of Origin TW:
Qty:
Part #:500377
- 3/4" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:501965
- 14" Extra-Long Cold Chisels
Designed for cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:507842
- 1/2" Drive SAE 3/4" Impact Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:507863
- 3/4" Drive SAE 3/4" Impact Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:513172
- Country of Origin CN:
Qty:
Part #:519071
- Country of Origin CN:
Qty:
Part #:501440
- 7" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Qty:
closeout
$6.76 MSRP
$
4.73
Part #:519062
- CLOSEOUTS Only 1 Left!
- Country of Origin CN:
Qty:
Part #:521106
- Specification
CATALOG NUMBER
01330
DESCRIPTION
SDS SHANK 3/4" X 12"
SHANK DIAMETER
3/4"
OVERALL LENGTH
12"
Qty:
Part #:519070
- Country of Origin CN:
Qty:
Part #:519057
- Country of Origin CN:
Qty:
Qty:
closeout
$49.56 MSRP
$
34.69
Part #:519086
- CLOSEOUTS Only 1 Left!
- Country of Origin US:
Qty:
Part #:811840
- 1/2" Drive SAE 3/4" Impact Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:702592
-
Category
Ball Valves
Subcategory
Brass & Bronze
Series Type
2 (Two) Piece
Threaded, 2-Piece, Std. Port, Bronze Ball Valve, w/Spring-Return Handle, 600 CWP, Sizes 1/4" to 2" (DN 8 to DN 50)
Qty:
Displaying: 1 - 24 of 60 Matching Items