Appleton
Aerokroil
View:
Active Filters :
Part #:511296
-
HIT-Z Anchor rod Anchor rod HIT-Z 5/8" x 9-1/2" #2018448Material, corrosionCarbon steel, zinc-platedWrench/nut size15/16 inDrill bit diameter3/4 inBase materialsConcrete (cracked), Concrete (uncracked)PROFIS SoftwareYesApprovals / Test reportsICC-ES report (concrete)Cleaning proceduresNon CleaningType of fixingPre-fastening, Through-fasteningProduct ClassUltimate
Qty:
Qty:
Part #:810222
- 1/2" Drive SAE 5/8" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Qty:
Qty:
Part #:508621
- Kwik Bolt 1 carbon steel wedge anchor
High-performance wedge anchor for cracked concrete and seismic (carbon steel)
Material, corrosionCarbon steel, zinc-plated
Head configurationExternally threaded
Drilling Method (AS)Hammer Drilling, Hollow Drill Bit Drilling
Material, corrosionCarbon steel, zinc-platedHead configurationExternally threadedDrilling Method (AS)Hammer Drilling, Hollow Drill Bit DrillingInstallation toolsTE 6-A36 Cordless rotary hammer, SIW 6AT-A22 Cordless impact wrench
Qty:
Part #:503703
- 5/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:134-J86058
- Made from S2 steel and specially heat-treated for greater strength and durability.
Hand-ground cutting edge to the exact angle for cutting through tough metals.
20% larger striking surface than standard chisels directs the power to the cutting edge.
Longer shank features a knurl for better grip and easy positioning.
Black oxide finish to help prevent rust corrosion extending tool life and performance.
Qty:
Qty:
Part #:501956
- 6 1/2" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Qty:
Part #:500704
- Kwik Bolt 1 carbon steel wedge anchor
High-performance wedge anchor for cracked concrete and seismic (carbon steel)
Material, corrosionCarbon steel, zinc-plated
Head configurationExternally threaded
Drilling Method (AS)Hammer Drilling, Hollow Drill Bit Drilling
Material, corrosionCarbon steel, zinc-platedHead configurationExternally threadedDrilling Method (AS)Hammer Drilling, Hollow Drill Bit DrillingInstallation toolsTE 6-A36 Cordless rotary hammer, SIW 6AT-A22 Cordless impact wrench
Qty:
Part #:509570
- 5/8" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:508626
-
HDI+ / HDI Flush anchor Drop-in anchor HDI 5/8" #336428Approvals / Test reportsFM (Factory Mutual), UL (Underwriter Laboratories)Material, corrosionCarbon steel, zinc-platedBase materialsConcrete (lightweight), Concrete (lightweight over metal deck), Concrete (uncracked)PROFIS SoftwareNoDrill bit diameter27/32 inProduct ClassPremium
Qty:
closeout
Part #:508596
- CLOSEOUTS Only 1 Left!
-
TE-CX (SDS Plus) Imperial hammer drill bit Hammer drill bit TE-CX 5/8"-6" #2153828 (Discontinued being replaced by Milwaukee 48-20-7200)
Connection end
TE-C (SDS Plus)Base materialReinforced concrete, Concrete, Brick, MasonryWorking modeHammer drillingHead shapeMulti CutterHead material compositionTungsten carbideNumber of cutting edges4Diameter5/8 inLength6 inWorking length4 inProduct ClassUltimate
$
71.87
Qty:
Part #:508634
-
Hand setting tool HST 5/8" #32981 HSD/HST 16-5/8 Setting tool
Manual setting tool for drop-in anchors (HDI-L/HDI/HDI-S/HDV)
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:507574
- Country of Origin US:
Qty:
Qty:
Displaying: 1 - 24 of 53 Matching Items