Chelsea
Band-It
View:
Active Filters :
closeout
$338.00 MSRP
$
240.63
Part #:505010
- CLOSEOUTS Only 2 Left!
- 1/2" Magnum® Drill, 0-850 RPM
Outperforms all other 1/2&rdquo drills in its category. The 1/2&rdquo Magnum® Drill has the power and construction to deliver long-lasting performance. The all-metal gear case and diaphragm provide high durability on the jobsite. The ergonomic, textured grip and two-finger trigger optimize user comfort and balance.
1/2" Magnum® Drill, 0-950 RPM (0234-6 Discontinued)
Built to handle industrial and construction applications with ease. The 1/2&rdquo Magnum® Drill has the raw power of a Milwaukee-built motor to perform in forward and reverse on wood, metal, plastics and composites. The exclusive brush system speeds brush changes to under one minute. Detach the QUIK-LOK® cord easily for storage or service replacement
Qty:
Part #:500695
- 1/2" Drive SAE 1/2" Long Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810245
- 6" Cold Chisels 1/2"
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:503702
- 1/2" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
closeout
$447.63 MSRP
$
294.99
Part #:805466
- CLOSEOUTS Only 1 Left!
- 1/2 in. Impact Wrench with Rocker Switch and Detent Pin Socket Retention
Delivers 300 ft-lbs of torque for faster installations. The 1/2" Impact Wrench with Rocker Switch and Detent Pin Socket Retention is designed to maximize your productivity. Its powerful 7.0-amp motor drives a unique impact mechanism that produces high torque and 1800 RPM for installation or loosening of bolts in less time. It features a detent pin to securely retain sockets or adapters, and a rocker switch for quick selection of forward or reverse. The ergonomically shaped handle has a soft cushioned grip, and provides a well-balanced and controllable feel to this lightweight tool.
Qty:
Part #:810220
- 1/2" Drive SAE 1/2" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810314
- 6" Center Punches
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
closeout
$384.00 MSRP
$
288.00
Part #:503780
- CLOSEOUTS Only 1 Left!
- 1/2" Hole-Hawg® Drill 300/1200 RPM (Replaced 1610-1)
Setting the standard for large-hole drilling in tight spaces. The 1/2" Hole-Hawg® Drill offers power and torque in a compact design that makes it perfect for drilling between studs and joists. The powerful motor features two speed ranges plus reverse for increased versatility. The drill offers a 4-5/8&rdquo self-feed bit capacity and an extra long pipe handle to help you control power.
Qty:
Part #:1184-JHWISFXT616
- 3/8" Drive 6-Point SAE 1/2" 6.57"/116.9mm Shank Length Tension Socket Flextension
Made in the U.S.A
Durable black oxide finish
Socket retention pin is TIG welded, providing full rotation power to the socket
Sockets feature SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Drive end has a 7/32" cross hole & bevel for ease of use
Up to 30 degree angle offset
Flextensions are designed for use on hand and power tools (Impulse or Direct drive) NOT FOR IMPACT TOOL USE
Maximum working torque values 160 Ft. Lbs. /1920 In. Lbs. /217 Nm
Other lengths and socket sizes available by special order. Contact your Snap-on Industrial Brands representative
Qty:
Part #:508595
- SDS-PLUS 4CT MX4&trade 1/2" X 10" X 12"(Discontinued, Being replaced by 48-20-8374)
Qty:
Part #:729-3601-20
- M18&trade Compact Brushless 1/2" Drill/ Driver
The MILWAUKEE® M18&trade ½&rdquo Compact Brushless Drill/Driver is more compact with faster speed in application. The compact drill is 5.7&rdquo in length and lightweight at 2.3 lbs without battery allowing for excellent control while working in overhead or tight spaces. The brushless motor was built to ensure optimal tool performance delivering 550 in-lbs of torque and 0-1,700 RPM, which makes this cordless drill able to tackle a wide range of drilling and fastening applications. REDLINK&trade Intelligence paired with MILWAUKEE® REDLITHIUM&trade M18&trade batteries ensures efficient power delivery resulting in less down time recharging batteries. The compact cordless drill has premium components with an all-metal gear case and ½&rdquo metal chuck providing durability that professionals require. The Compact Brushless ½&rdquo Drill/Driver is part of MILWAUKEE® M18&trade system, fully compatible with over 250+ solutions.
Qty:
Part #:811844
- 1/2" Drive SAE 1/2" Impact Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:509571
- 1/2" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:811596
- 3/8" Drive 6-Point SAE 1/2" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6-point fasteners
Qty:
Part #:811907
- 3/8" Drive 6-Point SAE 1/2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
Qty:
Displaying: 1 - 24 of 39 Matching Items