7/8"
1-1/16" - 1-1/2"
View:
Active Filters :
- Alt. Size: 1-1/16" - 1-1/2" 7/8" M10
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:810113
-
E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - M10-1.5 x 9/16-12
STRONG THREADS MADE EASY
All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools.
E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool.
E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes.
The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours).
Features
Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary)
Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product
Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps
Self-Locking pre-applied adhesive activates upon installation
Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out
Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi.
Applications
Soft metals aluminum, cast iron, magnesium, etc.
Installation
Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3.
Simply drill the appropriately sized hole with a standard drill
Tap the hole with a standard tap
Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool.
E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.
Qty:
Part #:810121
-
E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - M6-1.0 x M10-1.5
STRONG THREADS MADE EASY
All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools.
E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool.
E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes.
The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours).
Features
Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary)
Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product
Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps
Self-Locking pre-applied adhesive activates upon installation
Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out
Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi.
Applications
Soft metals aluminum, cast iron, magnesium, etc.
Installation
Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3.
Simply drill the appropriately sized hole with a standard drill
Tap the hole with a standard tap
Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool.
E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.
Qty:
Part #:810123
-
E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - M10-1.5 X M16-2.0
STRONG THREADS MADE EASY
All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools.
E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool.
E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes.
The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours).
Features
Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary)
Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product
Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps
Self-Locking pre-applied adhesive activates upon installation
Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out
Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi.
Applications
Soft metals aluminum, cast iron, magnesium, etc.
Installation
Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3.
Simply drill the appropriately sized hole with a standard drill
Tap the hole with a standard tap
Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool.
E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.
Qty:
Part #:810130
-
E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - 10-24 x M10-1.5
STRONG THREADS MADE EASY
All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools.
E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool.
E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes.
The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours).
Features
Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary)
Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product
Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps
Self-Locking pre-applied adhesive activates upon installation
Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out
Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi.
Applications
Soft metals aluminum, cast iron, magnesium, etc.
Installation
Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3.
Simply drill the appropriately sized hole with a standard drill
Tap the hole with a standard tap
Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool.
E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.
Qty:
Part #:502681
- SDS PLUS 4CT MX4&trade 7/8" X 16" X 18"
Our MX4&trade 4-Cutter SDS PLUS Rotary Hammer Drill Bits with solid head carbide deliver up to 5x longer life in concrete with rebar. Engineered with rebar guards to provide maximum durability in hard aggregate and rebar. We designed our MX4&trade 4-Cutter bits with sharp centering tips for exact spot drilling in concrete and metal decking. 4-cutter design prevents lock-up in rebar, reducing downtime. Variable flutes remove dust faster, reducing heat and delivering up to 20% more holes per battery charge. The wear mark indicator on each drill bit shows you when they no longer meet the ANSI requirement. These MILWAUKEE® MX4&trade 4-Cutter Drill Bits are ideal for concrete with rebar and masonry applications. Choose from single bits, bulk packs, or drill bit kits in a variety of sizes.
Qty:
Part #:508607
- TE-YX (SDS Max) Imperial hammer drill bit Hammer drill bit TE-YX 7/8"-13" #2165905
Connection endTE-Y (SDS Max)Base materialReinforced concrete, Concrete, Masonry, Brick, LimestoneWorking modeHammer drillingHead shapeMulti CutterHead material compositionTungsten carbideDiameter7/8 inLength13 inWorking length8 inProduct ClassUltimate
$
165.13
Qty:
Part #:811914
- 3/8" Drive 6-Point SAE 7/8" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
Qty:
$
4.25
FT
Qty:
Part #:503820
- Hex End L-Wrenches - ProGuard&trade Finish
Chamfered tool tips eliminate burrs and help tools seat in screw head
Sharp corners transfer more torque to the screw and reduce stripping
Precision machined for ease of use and superior fit
Qty:
Part #:503214
- Spline Bit 2-Cutter 7/8" x 16"
Milwaukee®'s Spline 2-Cutter Rotary Hammer drill bits are used for drilling intro brick, block, and concrete
Qty:
closeout
$39.88 MSRP
$
36.30
Part #:511852
- CLOSEOUTS Only 12 Left!
-
7/8" Wire Rope Clip, Forged Carbon Steel, Galvanized(Discontinued being replaced by 490-M253)
Base is Drop-Forged Carbon Steel
Hot Galvanized to ASTM A-153 to Resist Rust and Corrosion
U-Bolts Are colored Blue for Identification Purposes and Use Heavy Duty Hex Nuts (UNC-2A)
Designed to Meet Federal Specifications, FF-C-450, Type 1, Class 1
Designed to Meet or Exceed All Requirements of ASME B30.26 Including Identification, Ductility, Design Factor and Temperature
Permanently Marked with Size and Manufacturer
Sizes 1/4" and Above Marked with USA and Date Code
Sizes 1/8" Through 1-1/4" Are Supplied Bagged and Unassembled
Note See Application and Warning Information
Qty:
Part #:500456
- 1/2" Drive 12-Point SAE 7/8" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:500046
- 1/2" Drive 6-Point SAE 7/8" Deep Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
Qty:
Displaying: 25 - 48 of 77 Matching Items