1-1/4in
1-1/2in-11.50
View:
Active Filters :
- Size: 1-1/2in-11.50 1-1/4in 1/2in
Part #:303972
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$
4.61
Qty:
$
114.69
Qty:
Part #:305735
- Appleton and O-Z/Gedney Hang-On hangers are designed secure rigid metal conduit IMC or EMT to threaded rod supports or directly to mounting surfaces.
$
1.77
Qty:
Part #:306863
- Appleton combination couplings are used to couple flexible metal conduit to EMT conduit. Their armored cable and flexible metal conduit connectors are used to ground and secure armored ground wire armored cable nonmetallic sheathed cable and flexible metal conduit to boxes and enclosures.
$
7.61
Qty:
Part #:306877
- Type ABG A high strength corrosion-resistant copper alloy ground connector connecting a ground wire either parallel or at right angles to a ground rod or pipe. A positive ground is assured by the clamping pressure that can be applied by the high strength silicon bronze U-bolt, nuts and lock washers. Type ABG connectors are suitable for direct burial. For ground pipe larger than 1-1/2in use Type CG ground connector
Type CG For cable connection either parallel or at right angle to pipe. A high strength corrosion-resistant copper alloy ground connector having a reversible contact plate which permits the ground wire to be connected either at right angles or parallel to a ground pipe. The fitting is designed so that the saddle can be installed before the ground connection is made. High strength silicon bronze hardware permits high clamping pressures to be applied. Suitable for direct burial and wet locations. For ground pipe smaller than 2in use Type ABG
Type TG To attach, loosen the nut sufficiently to allow the end of the inJin bolt to slip over the flange, assemble the cable into the fitting and then tighten
Type KGM Copper alloy body and silicon bronze bolt, nut and lock washer combine strength and corrosion-resistance to insure a positive ground connection. HEX-CUP construction of the fitting simplifies installation by requiring only a single wrench for tightening
Type LG Installation of connectors is simplified by HEX-CUP construction. Cables are gripped by the interlocking clamp, used throughout the line of ground devices.
Copper alloy body and silicon bronze bolts, nuts and lock washers make a completely corrosion resistant fitting and permit high pressure to be applied - insuring a positive ground connection. Suitable for direct burial
Type ABG, Type CG and Type LG UL Listed and CSA Certified
Type TG CSA Certified
$
9.25
Qty:
Part #:306880
- O-Z/Gedney offers a variety of ground connectors. Type ABG and Type CG are used for connecting a ground wire either parallel or at right angles to a ground rod or pipe. Type TG is used for grounding H ?column fence posts. Its design eliminates the need for drilling the post. Type KGM features a one-piece design to connect a ground wire to any flat surface. Type LG one bolt design is used for connecting two parallel cables of the same or varying sizes to any flat surface
$
9.25
Qty:
$
9.25
Qty:
Part #:306946
- Appleton and O-Z/Gedney rigid conduit and IMC locknuts are used to secure and ground conduits and fittings to enclosures and prevents loosening due to vibration or motion. They are available in plain gasketed and bonding styles.
$
0.44
Qty:
Part #:306977
- Appleton and O-Z/Gedney conduit bushings are used with a locknut to terminate rigid metal conduit or IMC conduit to a box or enclosure. They provide a smooth pulling surface for wires.
$
0.34
Qty:
Part #:307005
- Appleton and O-Z/Gedney metallic knockout blanks and fixture stems are widely recognized for quality selection and ease of installation. They may be used as a junction box or a device box for switches receptacles GFCIs etc. Manufactured of durable materials with consistent construction means easy installation making all the difference in the speed and final quality of any wiring job.
$
0.72
Qty:
Part #:307122
- O-Z/Gedney threaded three piece couplings join two lengths of conduit when neither can be turned. Elbows provide a 90 change of direction in a conduit run. Gasket elbows also provide a compact wire pulling point.
$
26.76
Qty:
Part #:307195
- O-Z/Gedney threaded three piece couplings join two lengths of conduit when neither can be turned. Elbows provide a 90 change of direction in a conduit run. Gasket elbows also provide a compact wire pulling point.
$
12.07
Qty:
Part #:307297
- Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
$
15.35
Qty:
Part #:307347
- Appleton&trade offers beam clamps, straps, clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
$
0.60
Qty:
Part #:307972
- Appleton liquidtight STF Series connectors with threaded hubs are female ST Series connectors. They are designed to be used when making connection from liquidtight flexible metal conduit to threaded rigid conduit and IMC. The compact design results in a connector that offers a small turning radius.
$
7.78
Qty:
Part #:307975
- Appleton liquidtight STF Series connectors with threaded hubs are female ST Series connectors. They are designed to be used when making connection from liquidtight flexible metal conduit to threaded rigid conduit and IMC. The compact design results in a connector that offers a small turning radius.
$
24.71
Qty:
Part #:307984
- Appleton liquidtight ST Series plain throat and STB Series insulated throat connectors and external grounding lugs are for use with liquidtight flexible metal conduit where an external visible equipment bonding jumper is desired.
$
10.68
Qty:
Part #:307996
- Appleton aluminum liquidtight ST Series connectors with plain throat provide a dependable connection for liquidtight flexible metal conduit. Their lightweight aluminum construction facilitates installation. The compact design results in a connector that offers a small turning radius. They seal out oil water dust dirt and fumes.
$
11.34
Qty:
Part #:308001
- Appleton aluminum liquidtight ST Series connectors with plain throat provide a dependable connection for liquidtight flexible metal conduit. Their lightweight aluminum construction facilitates installation. The compact design results in a connector that offers a small turning radius. They seal out oil water dust dirt and fumes.
$
48.88
Qty:
Part #:308177
- O-Z/Gedney offers clamps and straps. They are used to secure oval/round cables or support runs of rigid metal conduit IMC and EMT.
$
0.22
Qty:
Part #:308313
- Appleton Form 35 Malleable Iron Conduit Outlet Bodies Covers and Gaskets are used to connect and change direction of conduit runs. In addition to making bends in a conduit system they allow connections for branch runs. These conduit bodies serve as pulling fittings and permit access to conductors for splicing and maintenance.
$
15.29
Qty:
Part #:308373
- Appleton Form 35 Malleable Iron Conduit Outlet Bodies Covers and Gaskets are used to connect and change direction of conduit runs. In addition to making bends in a conduit system they allow connections for branch runs. These conduit bodies serve as pulling fittings and permit access to conductors for splicing and maintenance.
$
19.10
Qty:
Part #:308410
- Appleton Form 85 Unilets Conduit Outlet Bodies Covers and Gaskets are used to connect and change direction of conduit runs. In addition to making bends in a conduit system they allow connections for branch runs. These conduit bodies serve as pulling fittings and permit access to conductors for splicing and maintenance.
$
5.26
Qty:
$
30.25
Qty:
Displaying: 25 - 48 of 1,655 Matching Items