6" x 4"
1-1/4"-7
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
$
4.95
Qty:
$
27.06
Qty:
Qty:
Qty:
Part #:810113
-
E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - M10-1.5 x 9/16-12
STRONG THREADS MADE EASY
All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools.
E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool.
E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes.
The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours).
Features
Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary)
Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product
Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps
Self-Locking pre-applied adhesive activates upon installation
Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out
Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi.
Applications
Soft metals aluminum, cast iron, magnesium, etc.
Installation
Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3.
Simply drill the appropriately sized hole with a standard drill
Tap the hole with a standard tap
Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool.
E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.
Qty:
Part #:502880
- SDS-PLUS 4CT MX4&trade 9/16" X 10" X 12
Our MX4&trade 4-Cutter SDS PLUS Rotary Hammer Drill Bits with solid head carbide deliver up to 5x longer life in concrete with rebar. Engineered with rebar guards to provide maximum durability in hard aggregate and rebar. We designed our MX4&trade 4-Cutter bits with sharp centering tips for exact spot drilling in concrete and metal decking. 4-cutter design prevents lock-up in rebar, reducing downtime. Variable flutes remove dust faster, reducing heat and delivering up to 20% more holes per battery charge. The wear mark indicator on each drill bit shows you when they no longer meet the ANSI requirement. These MILWAUKEE® MX4&trade 4-Cutter Drill Bits are ideal for concrete with rebar and masonry applications. Choose from single bits, bulk packs, or drill bit kits in a variety of sizes.
Qty:
Part #:502881
- TE-YX (SDS Max) Imperial hammer drill bit Hammer drill bit TE-YX 9/16" x 14" #206511
Ultimate SDS Max (TE-Y) hammer drill bit for exceptional concrete drilling performance (imperial)
Connection endTE-Y (SDS Max)
Base materialReinforced concrete, Concrete, Masonry, Brick, Limestone
Working modeHammer drilling
Connection end
TE-Y (SDS Max)Base materialReinforced concrete, Concrete, Masonry, Brick, LimestoneWorking modeHammer drillingHead shapeMulti CutterHead material compositionTungsten carbideNumber of cutting edges4Diameter9/16 inLength14 inWorking length8 inProduct ClassUltimate
$
142.73
Qty:
Part #:509135
-
TE-CX (SDS Plus) Imperial hammer drill bit Hammer drill bit TE-CX 9/16" x 18" #435017
Connection endTE-C (SDS Plus)Base materialReinforced concrete, Concrete, Brick, MasonryWorking modeHammer drillingHead shapeMulti CutterHead material compositionTungsten carbideNumber of cutting edges4Diameter9/16 inLength18 inWorking length15 inProduct ClassUltimate
$
122.35
Qty:
Part #:334-1315
- Pinch-On Double Ear Clamp Attributes
Weight
0.008 lb
Mandatory Package/Box Quantity
100
Material
Zinc Plated Steel
Nominal Size
9/16"
Range
.492" to .591" (12.5 mm to 15.0 mm)
$
0.71
Qty:
Part #:512222
- Spline Bit 2-Cutter 9/16" x 23"
Milwaukee®'s Spline 2-Cutter Rotary Hammer drill bits are used for drilling intro brick, block, and concrete
Qty:
Part #:729-49-59-2056
- 9/16" x 2" Annular Cutter
Dual alternating tooth geometry and thin-wall construction help Milwaukee&rsquos Annular Cutter cut up to 15% faster than the competition. With 20% thinner walls, the cutter displaces less material for the same size hole, giving you fast, burr-free holes in anything from sheet metal to thick steel plate.Milwaukee&rsquos proprietary high-speed steel with three hardness zones minimizes breakage and helps the bit last longer. It comes with a 3/4&rdquo Weldon shank, which is ideal for use with most small magnetic drill presses and large magnetic drill presses with the correct arbor.
Qty:
Part #:502877
-
TE-CX (SDS Plus) Imperial hammer drill bit Hammer drill bit TE-CX 9/16" x 6" #435015Ultimate SDS Plus (TE-C) hammer drill bit for anchor drilling into reinforced concrete (imperial)
Connection endTE-C (SDS Plus)
Base materialReinforced concrete, Concrete, Brick, Masonry
Working modeHammer drilling
Connection endTE-C (SDS Plus)Base materialReinforced concrete, Concrete, Brick, MasonryWorking modeHammer drillingHead shapeMulti CutterHead material compositionTungsten carbideNumber of cutting edges4Diameter9/16 inLength6 inWorking length4 inProduct ClassUltimate
$
58.06
Qty:
Part #:204133
- Description SDR35 Gasketed Fittings 6x4 TEE GxGxG
Qty:
Qty:
Qty:
Part #:207120
- Description SDR35 Gasketed Fittings 6x4 SADDLE WYE G
Qty:
Displaying: 25 - 48 of 71 Matching Items