1 gang
1-1/4"-7
Part #:304966
- Extremely durable for hard-use institutional applications. Spring-loaded covers close automatically when plugs are removed. Die-cast copper-free aluminum construction. Stainless steel springs. Screws and spring covers are chrome-plated brass. Baked-on lacquer finish. Heavy rubber gaskets provide positive seal. All covers below are for 4 screw mounting only. Comply with 2005 NEC Section 406.8(A) and 406.8(B)(2).
$
12.35
Qty:
Qty:
Qty:
Qty:
Part #:303701
- One Gang Heavy Cast Aluminum Cover Duplex Receptacle Horizontal, Gray
Extremely durable for hard-use institutional applications.
Spring-loaded covers close automatically when plugs are removed.
Die-cast copper-free aluminum construction.
Stainless steel springs.
Screws and spring covers are chrome-plated brass.
Baked-on lacquer finish.
Heavy rubber gaskets provide positive seal.
All covers below are for 4 screw mounting only.
Comply with 2005 NEC Section 406.8(A) and 406.8(B)(2).
CSA File Number 16807
Qty:
Part #:303205
- WP BOX 1G 3 HOLE 1/2 WPB23
Wide range of sizes, depths, and gangs.
Baked-on electrostatic, polyester, powder paint for superior scratch and corrosion resistance.
2 closure plugs and mounting lugs furnished with all boxes.
UL Listed for wet and/or damp locations with appropriate cover.
Designed for both interior and exterior applications.
Will accept standard 4 screw mounting covers and single gang weatherproof covers.
Simply strike desired knockout studs with a sharp hammer blow for clean mounting holes.
Heavy die-cast aluminum.
For covering patents, see www.legrand.us/patents.
CSA File Number 17695
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:811597
- 3/8" Drive 6-Point SAE 9/16" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6-point fasteners
Qty:
Part #:500375
- 9/16" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:307182
- Toggle Switch Openings, One Gang, 302/304 Stainless Steel
Type 302/304 Stainless Steel, non-magnetic .032''' nominal thickness.
Brushed finish.
This alloy contains 18% chromium and 8% nickel for superior resistance to corrosion.
Recommended for use in food processing plants, dairies, chemical plants, and other industrial, institutional, and commercial applications where corrosive atmospheres exist.
Standard, Jumbo, and Tandem plates available, as well as special Panel plates up to 5-gangs high and 10-gangs wide.
Packaged in protective film, with finish-matching screws.
Variety of special plated finishes.
Paintable to match plastic plates.
Can be silk-screened or engraved, and custom punched with over 300 opening styles.
Qty:
Part #:307185
- Duplex Receptacle Openings, One Gang, 302/304 Stainless Steel
Type 302/304 Stainless Steel, non-magnetic .032''' nominal thickness.
Brushed finish.
This alloy contains 18% chromium and 8% nickel for superior resistance to corrosion.
Recommended for use in food processing plants, dairies, chemical plants, and other industrial, institutional, and commercial applications where corrosive atmospheres exist.
Standard, Jumbo, and Tandem plates available, as well as special Panel plates up to 5-gangs high and 10-gangs wide.
Packaged in protective film, with finish-matching screws.
Variety of special plated finishes.
Paintable to match plastic plates.
Can be silk-screened or engraved, and custom punched with over 300 opening styles.
Qty:
Part #:503456
- 9/16" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:307154
- Blank Plates, Box Mounted, One Gang, Ivory
Molded of rugged, practically indestructible self-extinguishing nylon. ('TP' series only.)
Available in 'TP' series, extra 3/16 inch width and height than Standard size plates and 'TPJ' series, extra 3/16 inch width and height than Junior-Jumbo size plates.
Available in Ivory, White, Brown, Gray, Black, Blue, Orange, Red, and Light Almond.
Preferred for hospital, industrial, institutional, and other high-abuse applications.
Nominal thickness, .070 inch.
cULus ListingNumber 143222
Qty:
Part #:300310
- Single Gang Cast While-In-Use Cover, Gray
Compliant with National Electric Code (NEC) Section 406.8(B)(1) for wet locations.
UL listed for ''Extra-Duty'' applications.
Heavy cast aluminum construction.
Corner hinge allows for vertical or horizontal mounting.
Device inserts allow for multiple device types.
Install without removing electrical device thanks to keyed mounting holes.
Cord flap gaskets inhibit water splash and insects, all gaskets are factory installed.
Accepts padlocks.
Qty:
Part #:303196
- One Gang Blank Cover, Brushed Aluminum
Designed for both interior and exterior applications.
Universal aluminum mounting plates.
Gray, bronze and white models have baked-on electrostatic, polyester, powder paint for superior scratch and corrosion resistance.
CSA File Number 17695
Qty:
Part #:307371
- Weatherproof Single Gang Box, Gray
Wide range of sizes, depths, and gangs.
Baked-on electrostatic, polyester, powder paint for superior scratch and corrosion resistance.
2 closure plugs and mounting lugs furnished with all boxes.
UL Listed for wet and/or damp locations with appropriate cover.
Designed for both interior and exterior applications.
Will accept standard 4 screw mounting covers and single gang weatherproof covers.
Simply strike desired knockout studs with a sharp hammer blow for clean mounting holes.
Heavy die-cast aluminum.
For covering patents, see www.legrand.us/patents.
CSA File Number 17695
Qty:
Part #:300341
- Power Outlet Receptacle Openings, One Gang, 302/304 Stainless Steel
Type 302/304 Stainless Steel, non-magnetic .032''' nominal thickness.
Brushed finish.
This alloy contains 18% chromium and 8% nickel for superior resistance to corrosion.
Recommended for use in food processing plants, dairies, chemical plants, and other industrial, institutional, and commercial applications where corrosive atmospheres exist.
Standard, Jumbo, and Tandem plates available, as well as special Panel plates up to 5-gangs high and 10-gangs wide.
Packaged in protective film, with finish-matching screws.
Variety of special plated finishes.
Paintable to match plastic plates.
Can be silk-screened or engraved, and custom punched with over 300 opening styles.
Qty:
Part #:303227
- Wide range of sizes, depths, and gangs.
Baked-on electrostatic, polyester, powder paint for superior scratch and corrosion resistance.
2 closure plugs and mounting lugs furnished with all boxes.
UL Listed for wet and/or damp locations with appropriate cover.
Designed for both interior and exterior applications.
Will accept standard 4 screw mounting covers and single gang weatherproof covers.
Simply strike desired knockout studs with a sharp hammer blow for clean mounting holes.
Heavy die-cast aluminum.
For covering patents, see www.legrand.us/patents.
Qty:
Qty:
Qty:
Qty:
Displaying: 1 - 24 of 89 Matching Items