M16
2-1/4"
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:810123
-
E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - M10-1.5 X M16-2.0
STRONG THREADS MADE EASY
All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools.
E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool.
E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes.
The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours).
Features
Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary)
Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product
Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps
Self-Locking pre-applied adhesive activates upon installation
Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out
Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi.
Applications
Soft metals aluminum, cast iron, magnesium, etc.
Installation
Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3.
Simply drill the appropriately sized hole with a standard drill
Tap the hole with a standard tap
Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool.
E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.
Qty:
Part #:810125
-
E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - M12-1.75 x M16-2.0
STRONG THREADS MADE EASY
All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools.
E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool.
E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes.
The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours).
Features
Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary)
Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product
Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps
Self-Locking pre-applied adhesive activates upon installation
Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out
Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi.
Applications
Soft metals aluminum, cast iron, magnesium, etc.
Installation
Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3.
Simply drill the appropriately sized hole with a standard drill
Tap the hole with a standard tap
Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool.
E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.
Qty:
Part #:810357
- 3/4" Drive 12-Point SAE 2-1/4" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:729-49-57-2250
- 2-1/4" Threaded Steel Hawg Cutter
Drill holes up to 3X faster than twist drill bits with the Milwaukee® 3/4-inch Threaded Steel Hawg® Cutter. This long-lasting cutter features carbide teeth and an alternating cutting pattern to cut up to a 2" hole depth in steel, stainless steel, cast iron or aluminum. The spring-loaded, self-ejecting pin lets you make smoother, more accurate cuts and eject the plug faster.The Steel Hawg Cutter works with most electromagnetic drill presses. Use it with arbor 49-57-0030 for Milwaukee's 4262-1 magnetic drill press or arbor 49-57-0010 for Milwaukee's 4292-1 mag press. The 3/4" bit diameter has a metric thread size of M18 x 1.5" shank. Use the Threaded Steel Hawg with a No. 3 Morse Taper Arbor Assembly 49-57-0010.
Qty:
Part #:729-49-56-9215
- 2-1/4" BIG HAWG&trade with Carbide Teeth
MILWAUKEE® BIG HAWG&trade with Carbide Teeth is first-to-market in providing extreme life and durability in both nail-embedded wood and abrasive material applications. Utilizing advanced carbide technology to completely redesign the tried and true BIG HAWG&trade hole saw, the new BIG HAWG&trade with Carbide Teeth gives users 50x life in demanding applications with the ability to cut 1000+ more nails. 10X larger carbide teeth rip through materials 5X faster than any hole saw on the market, while oversized slots make for easy plug removal and chip ejection.
Qty:
Qty:
Qty:
Qty:
$
43.89
Qty:
Displaying: 1 - 24 of 25 Matching Items