4mm-0.70
3/4in x 1in
View:
Active Filters :
- Size: 3/4in x 1in 4mm-0.70
Qty:
Part #:506723
- Boss® Ground Joint Double Spud Attributes
Weight
1.02 lb
Size
3/4" and 1" (20mm and 25mm)
Material
Plated Steel
Seat
Polymer
Thread Size
3/4" and 1" (20mm and 25mm)
$
23.05
Qty:
Part #:204567
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:810120
-
E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - M4-0.7 x M8-1.25
STRONG THREADS MADE EASY
All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools.
E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool.
E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes.
The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours).
Features
Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary)
Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product
Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps
Self-Locking pre-applied adhesive activates upon installation
Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out
Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi.
Applications
Soft metals aluminum, cast iron, magnesium, etc.
Installation
Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3.
Simply drill the appropriately sized hole with a standard drill
Tap the hole with a standard tap
Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool.
E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.
Qty:
Qty:
Part #:204702
- Tees SAME END CONNECTIONS ON ALL THREE SIDES -22 CTS x -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Qty:
Qty:
Qty:
Part #:1128-12-16 CTX-S
- Performance Characteristics
Connection Type
37° Flare
Industry Standards
SAE J514
Maximum Dynamic Pressure (psi)
3000
Shape
90° Elbow
Connection Style
Tube to NPT
Connection 1 Style
Male 37° Flare
Connection 1 Tube O.D. (inch)
3/4
Connection 1 Tube O.D. (mm)
18, 20
Connection 2 Style
Male NPT/NPTF
Connection 2 Tube O.D. (inch)
na
Connection 2 Tube O.D. (mm)
na
Connection 2 Thread Size (inch)
1-11 1/2
Connection 2 Thread Size (mm)
na
Connection 3 Style
na
Connection 3 Tube O.D. (inch)
na
Connection 3 Tube O.D. (mm)
na
Connection 3 Thread Size (inch)
na
Connection 3 Thread Size (mm)
na
Connection 4 Style
na
Connection 4 Tube O.D. (inch)
na
Connection 4 Tube O.D. (mm)
na
O-Ring Material
na
Body Material
Steel, Chromium-6 Free
$
14.94
Qty:
Part #:130-5139-000
- Straight Ball Valves - Compression x FIP 90º ON/OFF TEE OPERATING HEAD, T CTS x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
182.85
Qty:
Displaying: 1 - 15 of 15 Matching Items