Anchor
3M
View:
Active Filters :
Qty:
Qty:
Part #:709473
- Ball Valves
Subcategory
Brass & Bronze
Series Type
2 (Two) Piece
Threaded, 2-Piece, Std. Port, Bronze Ball Valve, 600 CWP, Sizes 1/4" to 4" (DN 8 to DN 100)
Qty:
Part #:810356
- 1" Drive 12-Point SAE 1-1/2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:810217
- 1/2" Drive SAE 3/8" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:503700
- 3/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
Qty:
Part #:713136
-
Category Gates, Globes & Checks
Subcategory
Bronze
Series Type
Check Valve
Model No.
CVB
Threaded, Bronze In-Line Ball Cone Check Valve, Size 1/4" to 3" (DN 8 to DN 75)
Qty:
Part #:503686
- 3/8" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:810243
- 5 1/2" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
closeout
$241.00 MSRP
$
180.75
Part #:510336
- CLOSEOUTS Only 1 Left!
- 3/8" Magnum® Drill, 0-1200 RPM with All Metal Chuck and QUIK-LOK® cord
Get maximum versatility in this 3/8&rdquo workhorse drill. The 3/8&rdquo Magnum® Drill with All-Metal Chuck and QUIK-LOK® Cord features a powerful motor for optimal speed and torque for hole saws, twist bits and light fastening jobs. The all-metal gear case and diaphragm provide high durability on the jobsite. The ergonomic, tactile grip and two-finger trigger optimize your comfort and balance. Add the convenience and extra grip strength of the GRIP-LOK&trade chuck and a heavy-duty detachable cord, and you have unchallenged value.
Qty:
Part #:810313
- 5" Center Punches
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
Displaying: 1 - 24 of 65 Matching Items