Anchor
3M
View:
Active Filters :
Qty:
Qty:
Part #:700336
- Threaded, Unibody, Reduced Port, Stainless Steel Ball Valve, 2000 CWP to 1", 1500 CWP to 2", Sizes 1/4" to 2" (DN 8 to DN 50)
Qty:
Qty:
Part #:709156
-
Category
Ball Valves
Subcategory
Brass & Bronze
Series Type
3 (Three) Way
Threaded, Three-Way, Std. Port, Bronze Ball Valve,400 CWP, Sizes 1/4" to 2" (DN 8 to DN 50)
Qty:
Part #:709275
- Ball Valves
Subcategory
Brass & Bronze
Series Type
2 (Two) Piece
Threaded, 2-Piece, Std. Port, Bronze Ball Valve, 600 CWP, Sizes 1/4" to 4" (DN 8 to DN 100)
Qty:
Part #:712715
-
Category Gates, Globes & Checks
Subcategory
Bronze
Series Type
Check Valve
Model No.
CVB
Threaded, Bronze In-Line Ball Cone Check Valve, Size 1/4" to 3" (DN 8 to DN 75)
Qty:
Qty:
Qty:
Qty:
Part #:703030
-
Category
Ball Valves
Subcategory
Brass & Bronze
Series Type
2 (Two) Piece
Threaded, 2-Piece, Std. Port, Bronze Ball Valve, w/Spring-Return Handle, 600 CWP, Sizes 1/4" to 2" (DN 8 to DN 50)
Qty:
Part #:500381
- 15/16" 12-Point SAE SUPERCOMBO® Combination Wrench
Overview
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:507914
- 15/16" Drive 12-Point SAE 11/32" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:812981
- 12" Extra-Long Cold Chisels
Designed for cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:503706
- 1" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:810250
- 8" Cold Chisels 1"
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:507852
- 3/4" Drive SAE 15/16" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:503694
- 1" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:700936
-
Category
Ball Valves
Subcategory
Stainless Steel
Series Type
2 (Two) Piece
Threaded, 2-Piece, Std. Port, Stainless Steel Ball Valve, 2000 CWP to 1", 1500 CWP to 2", 1000 CWP to 3",Sizes 1/4" to 3" (DN 8 to DN 75)
Qty:
Displaying: 1 - 24 of 62 Matching Items