6-3/4in
1-5/8in
Part #:500566
-
#2 Twist Link Machine Chain, Zinc Plated, 100' per Carton
Uses General Utility Applications
Standard Material Low Carbon Steel
Standard Finish Bright, Zinc Plated and Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:500567
-
#35 Sash Chain, Zinc Plated, 100' per Carton
Counter-Balance Chain for Double Hung Window Sashes
Also for Arc Lamp Chain, Animal Chain
Standard Material Low Carbon Steel
Standard Finish Zinc Plated, Copper Glo, Solid Bronze
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:502824
-
2/0 Double Loop (Inco) Chain, Zinc Plated, 100' per Carton
Farm and Animal Chains, and Many General-Purpose Applications
Standard Material Low Carbon Steel
Standard Finish Zinc Plated, Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Note Avoid Twisting in Suspension Applications
Campbell Recommends The Use of Proof Coil or Straight Link Coil Chain for Swing Set Applications
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Qty:
Part #:502104
$
6.44
Qty:
Part #:502825
-
1/0 Double Loop (Inco) Chain, Zinc Plated, 100' per Reel
Farm and Animal Chains, and Many General-Purpose Applications
Standard Material Low Carbon Steel
Standard Finish Zinc Plated, Polycoated in White, Yellow, Green or Red Colors
Design Factor 4 to 1
Packaged on Reels, Order Unit is "Each"
Made in the USA
Note Avoid Twisting in Suspension Applications
Campbell Recommends The Use of Proof Coil or Straight Link Coil Chain for Swing Set Applications
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Qty:
Qty:
Qty:
Part #:513127
- 10 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
Qty:
Part #:503706
- 1" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:503494
-
4/0 Inco Double Loop Chain, Zinc Plated, 100' per Reel
Farm and Animal Chains, and Many General-Purpose Applications
Standard Material Low Carbon Steel
Standard Finish Zinc Plated, Polycoated in White, Yellow, Green or Red Colors
Design Factor 4 to 1
Packaged on Reels, Order Unit is "Each"
Made in the USA
Note Avoid Twisting in Suspension Applications
Campbell Recommends The Use of Proof Coil or Straight Link Coil Chain for Swing Set Applications
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:501654
-
1/0 Straight Link Machine Chain, Zinc Plated, 100' per Carton
Uses General Utility, Animal, and Farm and Ranch Applications
Standard Material Low Carbon Steel
Standard Finish Bright and Zinc Plated
Proof Tested
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:502827
-
#2 Double Loop (Inco) Chain, Zinc Coated, 100' per Carton
Farm and Animal Chains, and Many General-Purpose Applications
Standard Material Low Carbon Steel
Standard Finish Zinc Plated, Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Note Avoid Twisting in Suspension Applications
Campbell Recommends The Use of Proof Coil or Straight Link Coil Chain for Swing Set Applications
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:503092
-
1/0 Twist Link Machine Chain, Zinc Plated, 100' per Carton
Uses General Utility Applications
Standard Material Low Carbon Steel
Standard Finish Bright, Zinc Plated and Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:804793
-
#10 Single Steel Jack Chain, Zinc Plated, 100' per Carton
Fixture and Novelty Suspension
General Utility Use Not Requiring High Strength
Standard Material Low Carbon Steel
Standard Finish Zinc Plated
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Displaying: 1 - 24 of 30 Matching Items