9/16"
3/8"-24
Qty:
Qty:
Qty:
Part #:811597
- 3/8" Drive 6-Point SAE 9/16" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6-point fasteners
Qty:
Part #:500375
- 9/16" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:503456
- 9/16" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
$
4.95
Qty:
Qty:
Qty:
Qty:
Part #:810113
-
E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - M10-1.5 x 9/16-12
STRONG THREADS MADE EASY
All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools.
E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool.
E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes.
The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours).
Features
Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary)
Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product
Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps
Self-Locking pre-applied adhesive activates upon installation
Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out
Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi.
Applications
Soft metals aluminum, cast iron, magnesium, etc.
Installation
Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3.
Simply drill the appropriately sized hole with a standard drill
Tap the hole with a standard tap
Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool.
E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.
Qty:
Qty:
Displaying: 1 - 24 of 52 Matching Items