A.Y. Mcdonald Water Works
Armstrong International
View:
Active Filters :
Part #:802460
-
High quality liquid filled gauge
Vacuum and compound ranges through 0 psi to 15,000 psi
1-1/2", 2", 2-1/2" and 4" gauge sizes
Impact-resistant ABS and stainless steel case
Copper alloy and brass wetted parts
Qty:
Part #:804262
Qty:
Part #:804273
Qty:
Part #:203890
- Straight Adaptors ONE END FEMALE NATIONAL PIPE THREAD -22 CTS x FNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203964
- Straight Adaptors -22 CTS x MNPT ONE END MALE NATIONAL PIPE THREAD
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:713366
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:804270
Qty:
Part #:202743
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components conform to ASTM B62 and ASTM B584, UNS C83600• Certified to NSF/ANSI 61• Silicon Bronze bolts• EPDM o-ring• Pipe and tap size, and thread type identified on saddle• Outlet boss with large wrench flats:
$
55.70
Qty:
Part #:130-5122-156
- Elbows - 1/4 Bend. -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
$
941.74
Qty:
Qty:
Qty:
Part #:800543
- WARNING This product can expose you to chemicals including Nickel, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov
Qty:
Qty:
Qty:
Qty:
Part #:804264
Qty:
Part #:804276
$
78.10
Qty:
Part #:207154
- Straight Ball Valves - Female National Pipe Thread (FNPT) x Female National Pipe Thread (FNPT)
90º ON/OFF TEE OPERATING HEAD FNPT x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
673.49
Qty:
Part #:203943
- Straight Adaptors ONE END MALE NATIONAL PIPE THREAD Flare x MNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Displaying: 1 - 24 of 316 Matching Items