Hilti
Adhesives, Sealants, and Tapes
View:
Active Filters :
- Main Category: Adhesives, Sealants, and Tapes
- Brand: Hilti LA-CO Ors Nasco Inc Tesa
Part #:511262
-
HDM Manual adhesive dispenser Manual dispenser HDM 500 + black cartr #3498241
Manual hybrid/epoxy adhesive anchor dispenser
Dispenser typeManual
$
292.49
Qty:
Part #:511332
-
HIT-RE 500 V3 Epoxy anchor Epoxy adh RE 500-V3 11.1oz/330ml #2123401 Base materialsConcrete (cracked), Concrete (uncracked)Base material conditionDry, Submerged, Water-filled, WetApprovals / Test reportsICC-ES report (concrete)Seismic loadingYesPROFIS SoftwareYesClean-TecNoCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 158 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct informationThis product is subject to the Chemicals Prohibition Ordinance (ChemVerbotsV). It is to be used by professionals within the scope of their work and, in accordance with § 8 para. 3 no. 1 of the ChemVerbotsV, is to be used exclusively for its intended purpose as anchor adhesive, for rebar connections (typically steel-to-concrete and/or concrete-to-concrete connections), as well as for other intended fastening and uses within the scope of construction activities. Purchasers must comply with all existing legal requirements for the use of these products and may use them only as permitted. Information in the safety data sheets and operating instructions on the use of these products, the hazards associated with their use, the necessary safety measures during intended use and in the event of unforeseen spillage or release, and proper disposal must always be observed. The operating instructions and safety data sheets can be accessed in the detailed view of the products concerned at www.hilti.de in a format that can be saved and printed, and the operating instructions are enclosed with the products. Safety instructions Wear protective gloves/protective clothing/eye protection/face protection. Do not get in eyes, on skin or on clothing. In case of contact with eyes rinse thoroughly with water for several minutes. Remove contact lenses if possible, continue rinsing. If eye irritation, skin irritation or rash persist seek medical advice/attention. In case of contact with skin wash with plenty of soap and water. Disposal Completely emptied cartridges can be disposed of via the Dual System (yellow garbage can). Full/partially emptied containers are to be disposed of as special waste.Product ClassUltimate
$
81.77
Qty:
Part #:511731
-
HDM Manual adhesive dispenser Manual dispenser HDM 500 + red cartr #3498242
Manual hybrid/epoxy adhesive anchor dispenser
Dispenser typeManual
$
292.49
Qty:
$
44.92
Qty:
Part #:511740
-
Cartridge holder red HIT-CR 500 #2007059
$
45.81
Qty:
Part #:100022
- Country of Origin US UPC 48615420295:
Qty:
Part #:511331
-
HIT-HY 200-A V3 Adhesive anchor (New Verision)
Ultimate-performance injectable hybrid mortar with approvals for anchoring structural steel baseplate and post-installed rebar connections
Base materialsConcrete (cracked), Concrete (lightweight), Concrete (uncracked)
Approvals / Test reportsDOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, Seismic
PROFIS SoftwareYes
Base materialsConcrete (cracked), Concrete (lightweight), Concrete (uncracked)Approvals / Test reportsDOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, SeismicPROFIS SoftwareYesClean-TecNoCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Non CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 248 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct ClassUltimate
HIT-HY 200-A Adhesive anchor Hybrid adh HY 200-A 11.1oz/330ml #2022791 (Old Verision)Base materialsConcrete (cracked), Concrete (uncracked), Masonry (grout-filled CMU)Base material conditionDry, WetApprovals / Test reportsICC-ES report (concrete), SeismicSeismic loadingYesFatigue loadingNoFire resistanceNoPROFIS SoftwareYesClean-TecNoAnchoring elementsHAS threaded rods, HIS-N internally threaded sleeves, HIT-Z torque controlled bonded anchors, RebarCleaning proceduresAutomatic Cleaning (SafeSet Hollow Drill Bit), Compressed-Air Cleaning, Non CleaningStorage and transportation temperature range41 - 77 °FIn-service temperature &ndash range-40 - 248 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)12 monthsProduct ClassUltimate
$
64.39
Qty:
Part #:511683
-
HIT-HY 200-R Adhesive anchor Hybrid adh HY 200-R 11.1oz/330ml #2022793 Replaced By
HIT-HY 200-R V3 Adhesive anchor
Ultimate-performance injectable hybrid mortar with approvals for post-installed rebar connections and anchoring structural steel baseplate
Base materials Concrete (cracked), Concrete (lightweight), Concrete (uncracked)
Approvals / Test reports DOT approval (contact Hilti), ICC-ES report (concrete), ICC-ES report (masonry), LABC, Seismic
PROFIS Software Yes
$
64.39
Qty:
Part #:507221
-
HVU2 Anchor capsule Adhesive capsule HVU2 1/2" x 4 1/4" #2234721
Ultimate-performance foil capsule for heavy-duty anchoring in concrete
PROFIS SoftwareYes
Tested/approved for diamond drillingYes
In-service temperature &ndash range-40 - 248 °F
PROFIS SoftwareYesTested/approved for diamond drillingYesIn-service temperature &ndash range-40 - 248 °FStorage and transportation temperature range-4 - 77 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)24 monthsProduct ClassUltimate
Part #:103527
- Country of Origin US :
Qty:
Part #:521193
- Product description
tesa® 64613 is a high shear and high tensile poly-coated cloth tape providing easy hand-tearability and adhesion to a variety of different surfaces. It shows easy unwind and tears straight properties. Excellent for a variety of packaging, bundling and repair applications.
Technical properties
Elongation at break
16 %
Type of adhesive
natural rubber
Temperature resistance (30 min)
93 °C
Tensile strength
39 N/cm
Total thickness
190 µm
Backing material
PE laminated cloth
Adhesion to steel
4.95 N/cm
Mesh
27 count per square inch
$
8.44
Qty:
Part #:100060
- Features/Benefits
Pressures 500 PSI (34 BAR) for gas 5,000 PSI (340 BAR) for liquid
Sealing temperature -50°F to 350°F (-46°C to 177°C)
Contains PTFE particles for greater sealing power
Washes off hands and clothes easily quick and easy cleanup
Safe, non-toxic, non-drying
DO NOT USE ON OXYGEN SERVICE USE OXYTITE PASTE OR SLIC-TITE PTFE TAPE
Made in U.S.A.
Qty:
Part #:100285
- Markal® Slic-Tite® Paste Thread Sealants w/ PTFESpecially formulated with PTFE for added sealing power, Slic-tite is the premium thread sealant paste. It has been successfully used for decades to seal water, air, steam, natural gas, and more. It removes easily from skin and clothing, reducing post-job cleanup time. Slic-tite thread sealant works in extremely high-pressure systems, and it comes with several approvals to ensure industry standards are met.
Product DetailsUse PTFE Tape or Oxytite® PasteDo not use on oxygen serviceFor sealing water, air, steam, natural gas, LP gas, refrigerants, ammonia, gasoline and oilTesting and ApprovalsUSDA Approved for use in federally inspected meat and poultry plants CSA NSF UL ULC
Qty:
Part #:521556
- Adhesive capsule HVU2 7/8" x 6 5/8" #2234724Ultimate-performance foil capsule for heavy-duty anchoring in concrete
PROFIS SoftwareYesTested/approved for diamond drillingYesIn-service temperature &ndash range-40 - 248 °FStorage and transportation temperature range-4 - 77 °FShelf life from date of manufacture (at 73°F/23°C and 50% relative humidity)24 monthsProduct ClassUltimate
Part #:507560
- Adhesive capsule HVU2 3/8" x 3 1/2" #2234720
Ultimate-performance foil capsule for heavy-duty anchoring in concrete
PROFIS SoftwareYes
Tested/approved for diamond drillingYes
In-service temperature &ndash range-40 - 248 °F
$
175.93
BOX
Qty:
Part #:507222
- Adhesive capsule HVU2 5/8" x 5" #2234722
Ultimate-performance foil capsule for heavy-duty anchoring in concrete
PROFIS SoftwareYes
Tested/approved for diamond drillingYes
In-service temperature &ndash range-40 - 248 °F
Part #:507223
- Adhesive capsule HVU2 3/4" x 6 5/8" #2234723
Ultimate-performance foil capsule for heavy-duty anchoring in concrete
PROFIS SoftwareYes
Tested/approved for diamond drillingYes
In-service temperature &ndash range-40 - 248 °F
Displaying: 1 - 18 of 18 Matching Items