Apollo
Aerokroil
View:
Active Filters :
Part #:521021
Part #:701040
- 1/4in Jamesbury 9F Series/Eliminator 2000 Fire-Tite Threaded Ball Valve. Carbon steel body with stainless steel ball and stem. Jamesbury Xtreme seats with TFM seals. Non-ANSI Class Jamesbury Part # MA00038169FB2236XTB
Qty:
Part #:701171
- 1/4in Jamesbury 9F Series/Eliminator 2000 Fire-Tite Threaded Stainless Steel Ball Valve. Stainless steel body with stainless steel ball and stem. Jamesbury Xtreme seats with TFM seals. Non-ANSI Class Jamesbury Part # MA00113529FB3600XTB
Qty:
Part #:702627
- 1/4in Jamesbury 5H Value-Line Series High Pressure Threaded Ball Valve. Carbon steel body with stainless steel ball and 17-4PH stem. Seats are Acetal Homopolymer with PTFE seals. Jamesbury Part # MA0008363 5H22HBRT
Qty:
Part #:702851
- 1/4in Jamesbury Clincher Series 2000 2-Piece Threaded Ball Valve. Brass body with brass ball and stem. Seats and seals are PTFE. Assembled dry, no silicone. Jamesbury Part # MA0008357 211100TTC061
Qty:
Part #:709474
- Ball Valves
Subcategory
Brass & Bronze
Series Type
2 (Two) Piece
Threaded, 2-Piece, Std. Port, Bronze Ball Valve, 600 CWP, Sizes 1/4" to 4" (DN 8 to DN 100)
Qty:
Part #:503696
- 1/4" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
$
2.30
Qty:
Part #:521022
Part #:521023
Part #:521024
Part #:521025
Part #:701495
-
Category
Ball Valves
Subcategory
Carbon Steel
Series Type
2 (Two) Piece
Threaded, 2-Piece, Std. Port, Forged Carbon Steel Ball Valve, 2000 CWP to 1", 1500 CWP to 2", Sizes 1/4" to 2" (DN 8 to DN 50)
Qty:
Part #:709560
-
Category Ball Valves
Subcategory
Brass & Bronze
Series Type
2 (Two) Piece
Lead-Free NPT Bronze Ball Valve, 600 CWP, Sizes 1/4" to 4".
Qty:
Part #:810311
- 12" Long Taper Punches
Designed for aligning the holes in metal pieces through which rivets, bolts, or screws will be inserted
Not intended for driving pins as punch may become stuck in work
Also called line-up aligning or drift punches
Qty:
Part #:501675
- 1/2" Drive SAE 1/4" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810242
- 5" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
$
1.62
Qty:
$
2.72
Qty:
$
2.84
Qty:
$
4.82
Qty:
$
5.80
Qty:
$
4.14
Qty:
Part #:502010
- 3 7/8" Center Punches 1/4"
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
Displaying: 1 - 24 of 52 Matching Items