Appleton
Aerokroil
View:
Active Filters :
Part #:303913
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
Qty:
Part #:303962
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
Qty:
Part #:304000
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
Qty:
Part #:307124
- O-Z/Gedney threaded three piece couplings join two lengths of conduit when neither can be turned. Elbows provide a 90 change of direction in a conduit run. Gasket elbows also provide a compact wire pulling point.
Qty:
Part #:307977
- Appleton liquidtight STF Series connectors with threaded hubs are female ST Series connectors. They are designed to be used when making connection from liquidtight flexible metal conduit to threaded rigid conduit and IMC. The compact design results in a connector that offers a small turning radius.
Qty:
Part #:308003
- Appleton aluminum liquidtight ST Series connectors with plain throat provide a dependable connection for liquidtight flexible metal conduit. Their lightweight aluminum construction facilitates installation. The compact design results in a connector that offers a small turning radius. They seal out oil water dust dirt and fumes.
Qty:
Qty:
Qty:
Part #:203890
- Straight Adaptors ONE END FEMALE NATIONAL PIPE THREAD -22 CTS x FNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203964
- Straight Adaptors -22 CTS x MNPT ONE END MALE NATIONAL PIPE THREAD
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:300842
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
Qty:
Part #:302393
- Appleton and O-Z/Gedney offer ETP 4000S Series steel EMT set screw connectors. They are used to ground and secure EMT raceways to boxes and enclosures. The 4000S Series have a male NPS threaded hub and are available with or without an insulated throat.
Qty:
Part #:302432
- Appleton HUB-B threaded conduit hubs with bonding screw are general purpose fittings designed for RMC and IMC. They provide threaded terminations in sheet metal enclosures and are suitable for service entrances.
Qty:
Part #:302675
- Appleton and O-Z/Gedney offer ETP 5000S Series steel EMT set screw couplings. They are used to ground and secure EMT raceway sections together.
Qty:
Part #:306953
- Appleton and O-Z/Gedney rigid conduit and IMC locknuts are used to secure and ground conduits and fittings to enclosures and prevents loosening due to vibration or motion. They are available in plain gasketed and bonding styles.
Qty:
Part #:306984
- Appleton and O-Z/Gedney conduit bushings are used with a locknut to terminate rigid metal conduit or IMC conduit to a box or enclosure. They provide a smooth pulling surface for wires.
Qty:
Part #:307370
- Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
Qty:
Part #:307381
- Appleton and O-Z/Gedney offer NEER ECO aluminum entrance caps. They are a clamp type aluminum entrance cap for threaded or unthreaded rigid conduit IMC or EMT service masts.
Qty:
Part #:308184
- O-Z/Gedney offers clamps and straps. They are used to secure oval/round cables or support runs of rigid metal conduit IMC and EMT.
Qty:
Part #:308380
- Appleton Form 35 Malleable Iron Conduit Outlet Bodies Covers and Gaskets are used to connect and change direction of conduit runs. In addition to making bends in a conduit system they allow connections for branch runs. These conduit bodies serve as pulling fittings and permit access to conductors for splicing and maintenance.
Qty:
Part #:308415
- Appleton Form 85 Unilets Conduit Outlet Bodies Covers and Gaskets are used to connect and change direction of conduit runs. In addition to making bends in a conduit system they allow connections for branch runs. These conduit bodies serve as pulling fittings and permit access to conductors for splicing and maintenance.
Qty:
Part #:202743
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components conform to ASTM B62 and ASTM B584, UNS C83600• Certified to NSF/ANSI 61• Silicon Bronze bolts• EPDM o-ring• Pipe and tap size, and thread type identified on saddle• Outlet boss with large wrench flats:
$
55.70
Qty:
Part #:500505
- 3/4" Drive 12-Point SAE 2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:130-5122-156
- Elbows - 1/4 Bend. -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Displaying: 1 - 24 of 72 Matching Items