Appleton
Aerokroil
View:
Active Filters :
Part #:307293
- Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
Qty:
Part #:701040
- 1/4in Jamesbury 9F Series/Eliminator 2000 Fire-Tite Threaded Ball Valve. Carbon steel body with stainless steel ball and stem. Jamesbury Xtreme seats with TFM seals. Non-ANSI Class Jamesbury Part # MA00038169FB2236XTB
Qty:
Part #:701171
- 1/4in Jamesbury 9F Series/Eliminator 2000 Fire-Tite Threaded Stainless Steel Ball Valve. Stainless steel body with stainless steel ball and stem. Jamesbury Xtreme seats with TFM seals. Non-ANSI Class Jamesbury Part # MA00113529FB3600XTB
Qty:
Part #:702627
- 1/4in Jamesbury 5H Value-Line Series High Pressure Threaded Ball Valve. Carbon steel body with stainless steel ball and 17-4PH stem. Seats are Acetal Homopolymer with PTFE seals. Jamesbury Part # MA0008363 5H22HBRT
Qty:
Part #:702851
- 1/4in Jamesbury Clincher Series 2000 2-Piece Threaded Ball Valve. Brass body with brass ball and stem. Seats and seals are PTFE. Assembled dry, no silicone. Jamesbury Part # MA0008357 211100TTC061
Qty:
Qty:
Qty:
Qty:
Part #:503696
- 1/4" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:500383
- 1-1/16" 12-Point SAE SUPERCOMBO® Combination Wrench
Overview
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:810311
- 12" Long Taper Punches
Designed for aligning the holes in metal pieces through which rivets, bolts, or screws will be inserted
Not intended for driving pins as punch may become stuck in work
Also called line-up aligning or drift punches
Qty:
Part #:811834
- 1/2" Drive SAE 1-1/16" Impact Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:501675
- 1/2" Drive SAE 1/4" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810242
- 5" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:307345
- Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
Qty:
Part #:307361
- Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
Qty:
Part #:502010
- 3 7/8" Center Punches 1/4"
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
Qty:
Qty:
Qty:
Displaying: 1 - 24 of 76 Matching Items