Armstrong International
Apollo
View:
Active Filters :
Part #:505685
- Technical Specs Item Multipurpose Grease NLGI Grade 2 Base Oil Synthetic Container Size 14 oz NSF Rating H1 Food Grade Grease Thickener Calcium Sulfonate Grease Color Tan Grease Container Cartridge Max. Operating Temp. 500 Degrees F Flash Point 350 Degrees F Dropping Point 500 Degrees F Four-Ball Wear Not Specified Specific Gravity 0.95 Timken OK Load Not Specified Standards CFIA, Category Code H-1, NSF Registered Application Equipment, Machine Parts, Use as Anti Rust Film on Bearings, or as a Release Agent on Gaskets/Seals
Qty:
Part #:509133
- Technical Specs Item Retaining Compound Shear Strength (PSI) 2,300 psi Optimal Usage Temperature -65 Degrees to 300 Degrees F Gap Fill Size 0.006 in Container Type - Adhesives Bottle Container Size - Adhesives 0.34 oz Series Retaining Compounds Physical Form Liquid Max. Temp. (F) 300 Degrees F Full Cure 24 hr Primer T Compound Type Fast Cure, General Purpose Low Viscosity Application Press Fit or Slip Fit/Housing Mount, Press Fit, Shaft Mount Characteristics Green Standards ASTMD-5363, CFIA Listed, Mil-R-460B
$
20.41
Qty:
Part #:713381
- Float and Thermostatic (F&T) Steam TrapsThe More Your Steam Pressure Varies, The More You Need Armstrong F&T TrapsWhen steam pressure may vary from maximum steam supply pressure to vacuum, Armstrong F&Ts are your most energy-efficient choice. Our line of F&Ts brings Armstrong performance, dependability and long life to trapping services requiring continuous drainage with high air venting capacity. Thanks to separate orifices for condensate and air, they provide continuous condensate drainage and air venting-even under conditions of zero pressure. All the benefits detailed here have been designed into Armstrong F&Ts through long experience in the manufacture of pressure float-type traps. They assure you of optimum operating efficiency for long periods with minimum trouble. How they work Float and thermostatic traps are mechanical units that operate on both density and temperature principles. The float valve operates on the density principle. A level connects the ball float to the valve and seat. Once condensate reaches a certain level in the trap, the float rises, opening the orifice and draining condensate. A water seal formed by the condensate prevents live steam loss. Since the discharge valve is under water, it is not capable of venting air and non-condensables. When the accumulation of air and con-condensable gases causes a significant temperature drop, a thermostatic air vent in the top of the trap discharges them. The thermostatic vent opens at a temperature a few degrees below saturation, so it's able to handle a large volume of air-through an entirely separate orifice-but at a slightly reduced temperature. Built as tough as the jobs they do Armstrong float and thermostatic traps are unique in their super heavy duty construction. Armstrong uses high quality ASTM A48 Class 30 cast iron or ASTM A216 WCB cast steel-normally found in pressure vessels rated to 250 psi (17 bar) or 465 psi (32 bar). Internal mechanisms are made from stainless steel and are heavily reinforced. No brass cotter pins here. Valves and seats are stainless steel, hardened, ground and lapped to withstand the erosive forces of flashing condensate. Why go to all this trouble for traps normally recommended for low-pressure, modulating service? The operative word here is modulating. Modulating pressures mean widely varying loads, thermal cycling and high air and non-condensable gas loads. In other words tough service. Inferior, lightweight construction in this kind of service is a mistake waiting to happen. Trap failures on modulating pressure may lead to water hammer, corrosion and even damage to heat exchangers. Armstrong's published capacities are based on actual measurements of traps handling hot, flashing condensate. Competitive F&Ts may utilize theoretical calculated capacities. Armstrong uses its own steam lab to give you actual capacity-especially important on high-capacity traps such as those in our ultra-capacity line. Not only does Armstrong offer super heavy duty construction for long life and reliability, but we also supply the data to back up performance. Here's a simple, easy-to-remember summary The more your pressure varies, the more you need Armstrong F&Ts.
Qty:
Part #:1184-JHW8-7
- 1-1/2" Drive Adapter 1-1/2" Female x 1" Male 4-1/4"
&bull Specially heat treated for impact use to provide long life, safety, and durability
&bull Pin and o-ring or RET RING® (sold separately) secure tools onto impact wrench for safety and convenience
&bull Universal joint provides 55° range of motion
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Drive end features pin retention hole and groove
Qty:
Qty:
Qty:
Qty:
closeout
$
14.15
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
Displaying: 73 - 96 of 2,287 Matching Items