Armstrong International
J.H. Williams
View:
Active Filters :
- Brand: J.H. Williams Armstrong International
- Alt. Size: 1/2"
Part #:810245
- 6" Cold Chisels 1/2"
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:500695
- 1/2" Drive SAE 1/2" Long Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:503702
- 1/2" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:713360
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:810314
- 6" Center Punches
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
Part #:810220
- 1/2" Drive SAE 1/2" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:701257
- The most reliable steam trap known&mdashthe inverted bucket&mdashprovides efficientcondensate drainage of virtually all types of steam-using equipment. Putthe inverted bucket to work in a tough cast iron package, and you have thebest of both worlds. Because they operate efficiently for longer periods oftime, Armstrong cast iron inverted buckets add solid energy savings to lowerreplacement/labor costs. All Armstrong cast iron inverted bucket steam trapsare repairable for even bigger maintenance savings.
A unique leverage system multiplies the force provided by the bucket to openthe valve against system pressure. The mechanism is free-floating, and hasno fixed pivots to create wear or friction.
Because the mechanism is located at the top of the trap, no dirt can collecton the orifice. Small particles of dirt are held in suspension until dischargedby the full differential purging action when the bucket sinks, pulling the valveoff the seat.
The discharge orifice is surrounded by a water seal, preventing live steamloss. Automatic air venting is provided by a small vent hole in the bucket, whichprovides continuous automatic air and CO2 venting at steam temperature.Inverted bucket traps drain continuously, although discharging intermittently,allowing no condensate backup. They are also resistant to water hammer.
Qty:
Part #:710287
- The most reliable steam trap known&mdashthe inverted bucket&mdashprovides efficientcondensate drainage of virtually all types of steam-using equipment. Putthe inverted bucket to work in a tough cast iron package, and you have thebest of both worlds. Because they operate efficiently for longer periods oftime, Armstrong cast iron inverted buckets add solid energy savings to lowerreplacement/labor costs. All Armstrong cast iron inverted bucket steam trapsare repairable for even bigger maintenance savings.
A unique leverage system multiplies the force provided by the bucket to openthe valve against system pressure. The mechanism is free-floating, and hasno fixed pivots to create wear or friction.
Because the mechanism is located at the top of the trap, no dirt can collecton the orifice. Small particles of dirt are held in suspension until dischargedby the full differential purging action when the bucket sinks, pulling the valveoff the seat.
The discharge orifice is surrounded by a water seal, preventing live steamloss. Automatic air venting is provided by a small vent hole in the bucket, whichprovides continuous automatic air and CO2 venting at steam temperature.Inverted bucket traps drain continuously, although discharging intermittently,allowing no condensate backup. They are also resistant to water hammer.
Qty:
Part #:811844
- 1/2" Drive SAE 1/2" Impact Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:811907
- 3/8" Drive 6-Point SAE 1/2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
Qty:
Part #:811596
- 3/8" Drive 6-Point SAE 1/2" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6-point fasteners
Qty:
Part #:1184-JHWISFXT616
- 3/8" Drive 6-Point SAE 1/2" 6.57"/116.9mm Shank Length Tension Socket Flextension
Made in the U.S.A
Durable black oxide finish
Socket retention pin is TIG welded, providing full rotation power to the socket
Sockets feature SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Drive end has a 7/32" cross hole & bevel for ease of use
Up to 30 degree angle offset
Flextensions are designed for use on hand and power tools (Impulse or Direct drive) NOT FOR IMPACT TOOL USE
Maximum working torque values 160 Ft. Lbs. /1920 In. Lbs. /217 Nm
Other lengths and socket sizes available by special order. Contact your Snap-on Industrial Brands representative
Qty:
Part #:509571
- 1/2" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:500374
- 1/2" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:808633
- 1/2" Drive SAE 1/2" Impact Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:500441
- 3/8" Drive 12-Point SAE 1/2" Shallow Socket
&bull All tools are professional quality, made of high-grade chrome vanadium steel
&bull Sockets feature SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Metal tool box made for years of rugged use
Qty:
Part #:812895
- 3/8" Drive 12-Point SAE 1/2" Deep Socket
All tools are professional quality, made of high-grade chrome vanadium steel
Sockets feature SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Metal tool box made for years of rugged use
Qty:
Part #:501122
- 1/2" 12-Point SAE SUPERCOMBO® Black Industrial Finish Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:500450
- 1/2" Drive 12-Point SAE 1/2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:500470
- 1/2" Drive 12-Point SAE 1/2" Deep Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:501423
- 1/4" Drive 6-Point SAE 1/2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
Qty:
Part #:811434
- 1/4" Drive 12-Point SAE 1/2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:509447
- 1/4" Drive 6-Point SAE 1/2" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Qty:
Part #:812805
- 1/4" Drive 12-Point SAE 1/2" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for quick engagement on both 6 and 12-point fasteners
Qty:
Displaying: 1 - 24 of 345 Matching Items