Armstrong International
UNP Polyvalves
View:
Active Filters :
- Brand: UNP Polyvalves Armstrong International
- Alt. Size: 4"
Part #:501-D25979
- DS Series In-Line Condensate SeparatorsDuctile Iron Drain SeparatorCondensate in steam and air piping reduces thermal efficiency, causes water hammer, corrodes equipment such as valves and pipes, and causes other problems.
In-line (drain) separators DS-1, DS-2, DS-3, and DS-4 separate condensate efficiently by using the centrifugal force of steam or air created by introducing it into a specifically shaped path. Because of the simple structure of the drain separators, pressure loss is minimized, enabling clean, dry steam or air to be fed to equipment.
When steam or air flow enters the drain separator, centrifugal force is generated in the fluid because of the devices internal structural design. The fluid drains along the wall because of the difference in specific gravity with steam or air, eventually striking the baffle. The baffle guides the fluid to the drain outlet and to the trap, which drains it. As a result, small dirt particles and condensate are separated and removed from the system through the bottom drain.
• Cyclone structure maximizes liquid separation efficiency
• Pressure loss is extremely low
• No moving parts means no breakdowns
Qty:
Part #:501-D25980
- DS Series In-Line Condensate SeparatorsDuctile Iron Drain SeparatorCondensate in steam and air piping reduces thermal efficiency, causes water hammer, corrodes equipment such as valves and pipes, and causes other problems.
In-line (drain) separators DS-1, DS-2, DS-3, and DS-4 separate condensate efficiently by using the centrifugal force of steam or air created by introducing it into a specifically shaped path. Because of the simple structure of the drain separators, pressure loss is minimized, enabling clean, dry steam or air to be fed to equipment.
When steam or air flow enters the drain separator, centrifugal force is generated in the fluid because of the devices internal structural design. The fluid drains along the wall because of the difference in specific gravity with steam or air, eventually striking the baffle. The baffle guides the fluid to the drain outlet and to the trap, which drains it. As a result, small dirt particles and condensate are separated and removed from the system through the bottom drain.
• Cyclone structure maximizes liquid separation efficiency
• Pressure loss is extremely low
• No moving parts means no breakdowns
Qty:
Part #:501-D27089
- AEH Series Exhaust Heads Armstrongs AEH series carbon steel exhaust heads should be used when there is a risk of water carryover up an atmospheric vent pipe. The internal knock-out plate and stainless steel mesh screening effectively contains water carry-over and discharges it through the bottom drain leaving dry flash steam to vent through the top of the vessel.
Connections
• Flanged ASME B16.5 CL 150
• Drain FNPT
Qty:
Part #:501-D29066
- DS Series In-Line Condensate SeparatorsCarbon Steel Drain SeparatorCondensate in steam and air piping reduces thermal efficiency, causes water hammer, corrodes equipment such as valves and pipes, and causes other problems.
In-line (drain) separators DS-1, DS-2, DS-3, and DS-4 separate condensate efficiently by using the centrifugal force of steam or air created by introducing it into a specifically shaped path. Because of the simple structure of the drain separators, pressure loss is minimized, enabling clean, dry steam or air to be fed to equipment.
When steam or air flow enters the drain separator, centrifugal force is generated in the fluid because of the devices internal structural design. The fluid drains along the wall because of the difference in specific gravity with steam or air, eventually striking the baffle. The baffle guides the fluid to the drain outlet and to the trap, which drains it. As a result, small dirt particles and condensate are separated and removed from the system through the bottom drain.
• Cyclone structure maximizes liquid separation efficiency
• Pressure loss is extremely low
• No moving parts means no breakdowns
Qty:
Part #:501-D33865
- DS Series In-Line Condensate SeparatorsCarbon Steel Drain SeparatorCondensate in steam and air piping reduces thermal efficiency, causes water hammer, corrodes equipment such as valves and pipes, and causes other problems.
In-line (drain) separators DS-1, DS-2, DS-3, and DS-4 separate condensate efficiently by using the centrifugal force of steam or air created by introducing it into a specifically shaped path. Because of the simple structure of the drain separators, pressure loss is minimized, enabling clean, dry steam or air to be fed to equipment.
When steam or air flow enters the drain separator, centrifugal force is generated in the fluid because of the devices internal structural design. The fluid drains along the wall because of the difference in specific gravity with steam or air, eventually striking the baffle. The baffle guides the fluid to the drain outlet and to the trap, which drains it. As a result, small dirt particles and condensate are separated and removed from the system through the bottom drain.
• Cyclone structure maximizes liquid separation efficiency
• Pressure loss is extremely low
• No moving parts means no breakdowns
Qty:
Part #:501-D503469
- A/CA Series Cast Iron Y-Type Pipe Strainer Y-Type Cast Iron Strainer
• 250lb Screwed 1/2in - 3in
• Class 125 Flanged 2in - 6in
• Class 250 Flanged 2in - 6inScreen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:501-FH1367
- Pumping TrapsArmstrong pump traps offer the following features, advantages and benefits
Non-electric
Utilizes inexpensive steam, air or gas for operation and has no seals, motors, impellers or electric components, which frequently fail.
Wear and corrosion resistance.
Mechanism frame assembly is constructed of rugged investment-cast stainless steel components.
Stress chloride corrosion resistance
Inconel X-750 springs have higher resistance to the stress that causes lower-grade stainless steel springs to fail.
Corrosion resistance
Entire float mechanism is stainless steel. Float is Heliarc welded to avoid the introduction of dissimilar metals, which could lead to galvanic corrosion and float failure.
Externally replaceable valve and seat assembly
Maintenance is a "snap" with hardened stainless steel valves that can be cleaned or replaced without cap removal.
Explosion proof
Intrinsically safe due to all-stainless steel construction of mechanism.
Long life and dependable service.
Simple float/spring operation and rugged all-stainless steel construction allow for long, trouble-free service life.
Compact, low-profile design
Low-profile design allows for maximum pump capacity with minimal fill head and floor space requirements. PT-300 Series horizontal tank design provides the highest capacity with the lowest profile on the market.
Qty:
Part #:5032-BVFPC1T2L1F5GY04
- 2in UNP Polyvalve 150lb Full Port PFA Lined Ball Valve. 3M Dyneon PFA lined carbon steel body with PFA encapsultated ball and duplex stainless steel stem. Seats are specialized TFM/MPTFE for lower torque, increased durability, and expanded life. Includes locking handle.UNP Polyvalve Part # BVFPC1T2L1F5LY02Projects and Crossover OpportunitiesThrough UNP Polyvalve we are able to offer high quality products at a competitive price. If you have an opportunity to crossover a competing lined valve product to UNP please contact us. Smaller quantities may ship from stock while the largest projects are delivered in approximately 14 weeks. Some products to replace with our UNP valves include- Xomox 2in XLB12A1P628P16H- ChemTite BO-03-A-02-O, BO-03-B-02-OReplaces Xomox XLB series, Hills-McCanna ChemTite BO or BV series, Flowserve AKH2A series, ITT Richter BVA or KA series
UNP Polyvalve USA &ndash Teflon Lined ValvesUNP is one of the top global suppliers of lined valves and is positioned strongly to provide top quality products with segment leading lead times on lined valve, pipe, and fitting project quantities.Product Features and Available OptionsHigh quality UNP lined valves use a floating ball design for reduced port and integral ball and stem design for full port ball valves. All valves use Chevron packings (sintered packings) and are subjected to factory Helium Leak tests. The UNP lining is anchored with dove tail grooves which make the valves suitable for both pressure and vacuum applications.The standard PFA lined ball valve that we offer is full port, however reduced port can be offered by special order.Any lined valve is an investment as they are typically used in critical applications. Quality valves will help reduce downtime and increase operational efficiency. With that understanding, UNP has made the standard body casting material ASTM A 216 Grade WCB carbon steel. UNP offers all metal components in investment castings, ensuring intact and homogeneous lining and having an overall even thickness of lining at intricate contours. Stainless steel CF8M bodies are available for special order as well. Unlike the UNP investment casting, many competing valve manufacturers use ductile iron valve bodies.UNP uses top of the line, virgin raw materials such as PFA linings exclusively made from Dyneon PFA from 3M. The careful selection of materials and specified high purity grades, enables end product use in a wide range of applications from critical industrial systems to the pharmaceutical and food industries.The lining for all UNP valves uses the latest injection molding process and not by transfer molding process makes its lining more compact and reliable.Our standard UNP ball valve uses 3M Dyneon PFA lining, however special orders are available with Conductive PFA, PTFE, FEP, PVDF, ETFE, ECTFE and PPH.In line with today&rsquos automation standards, our UNP Valves are all designed with an ISO mounting pad to enable easy actuator mounting. Actuators, limit switches, solenoids, valves positioners and other automation components are all available to be added to your lined valve order.UNP subjects all of its valves to both Hydro and Pneumatic Test ensuring 100% reliability for performance of valves under pressure. UNP valves are SIL3 certified as well.
$
2,198.00
Qty:
Displaying: 1 - 8 of 8 Matching Items