Armstrong International
Bussmann Division


Displaying: 1 - 12 of 12 Matching Items
12 Items
View:
Active Filters :
$52.38 MSRP $ 21.48
Qty:
add to cart
$58.38 MSRP $ 23.94
Qty:
add to cart
$56.58 MSRP $ 23.20
Qty:
add to cart
Part #:785-1406080
Unshielded Rubber Coupling 6" Corrugated x 6" Cast Iron/Plastic
$ 79.53
Qty:
add to cart
Part #:202642
0706028:
$16.43 MSRP $ 15.33
Qty:
add to cart
$ 50.88
Qty:
add to cart
Part #:501-D27090
AEH Series Exhaust Heads Armstrongs AEH series carbon steel exhaust heads should be used when there is a risk of water carryover up an atmospheric vent pipe. The internal knock-out plate and stainless steel mesh screening effectively contains water carry-over and discharges it through the bottom drain leaving dry flash steam to vent through the top of the vessel. Connections &#8226 Flanged ASME B16.5 CL 150 &#8226 Drain FNPT
$4,024.00 MSRP $ 3,318.04
Qty:
add to cart
Part #:501-D39124
DS Series In-Line Condensate SeparatorsCarbon Steel Drain SeparatorCondensate in steam and air piping reduces thermal efficiency, causes water hammer, corrodes equipment such as valves and pipes, and causes other problems. In-line (drain) separators DS-1, DS-2, DS-3, and DS-4 separate condensate efficiently by using the centrifugal force of steam or air created by introducing it into a specifically shaped path. Because of the simple structure of the drain separators, pressure loss is minimized, enabling clean, dry steam or air to be fed to equipment. When steam or air flow enters the drain separator, centrifugal force is generated in the fluid because of the devices internal structural design. The fluid drains along the wall because of the difference in specific gravity with steam or air, eventually striking the baffle. The baffle guides the fluid to the drain outlet and to the trap, which drains it. As a result, small dirt particles and condensate are separated and removed from the system through the bottom drain. &#8226 Cyclone structure maximizes liquid separation efficiency &#8226 Pressure loss is extremely low &#8226 No moving parts means no breakdowns
$11,607.00 MSRP $ 9,509.35
Qty:
add to cart
Part #:501-D502638
A/CA Series Cast Iron Y-Type Pipe Strainer Y-Type Cast Iron Strainer &#8226 250lb Screwed 1/2in - 3in &#8226 Class 125 Flanged 2in - 6in &#8226 Class 250 Flanged 2in - 6inScreen chambers won't leak or crush Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen. Screwed retainers easy in, easy out Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads. Off-center blowdown connections for better dirt removal Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed. Many screen choices Many screen materials, meshes and perforations are available.
$4,114.00 MSRP $ 3,362.07
Qty:
add to cart
Part #:206008
Shielded 6" Clay x 6" Cast Iron/Plastic
$ 117.00
Qty:
add to cart
 
Displaying: 1 - 12 of 12 Matching Items