Columbus McKinnon (C-M)
Armstrong International
View:
Active Filters :
closeout
$338.00 MSRP
$
240.63
Part #:505010
- CLOSEOUTS Only 2 Left!
- 1/2" Magnum® Drill, 0-850 RPM
Outperforms all other 1/2&rdquo drills in its category. The 1/2&rdquo Magnum® Drill has the power and construction to deliver long-lasting performance. The all-metal gear case and diaphragm provide high durability on the jobsite. The ergonomic, textured grip and two-finger trigger optimize user comfort and balance.
1/2" Magnum® Drill, 0-950 RPM (0234-6 Discontinued)
Built to handle industrial and construction applications with ease. The 1/2&rdquo Magnum® Drill has the raw power of a Milwaukee-built motor to perform in forward and reverse on wood, metal, plastics and composites. The exclusive brush system speeds brush changes to under one minute. Detach the QUIK-LOK® cord easily for storage or service replacement
Qty:
Part #:522112
- 18 TPI Compact Portable Band Saw Blade 3PK
Maximize your compact band saw performance and make straight, accurate cuts in a variety of materials with the Milwaukee® 18 TPI Compact Portable Band Saw Blade (3-Pack). Get long tooth life and exceptional durability when cutting a variety of metal, including strut, conduit, angle iron, copper tube, threaded rod and pipe. The blade's tooth form, pitch and set ensure straight, accurate cuts time and time again.
Qty:
$
448.55
Qty:
Part #:510283
- CM Series 632
close radius trolley With revolutionary advances, this shorter, more compact
trolley is 50% lighter than competitive trolleys, yet every bit
as tough. Negotiates radius curves as tight as 7 to 10 inches
Made of highest quality rolled steel
Unique double row, ball bearing wheel design
for greater wear capacity
Larger V-bars available for wider flange adjustment
For low headroom applications
Bearings prepacked with lifetime lubricant
Exclusive Dial-Fit collar quickly adapts trolley to
wide range of beams and patented rails
Dust covers shield and protect bearings
Trolleys available for larger beams, rails or tracks
contact CM
Cast iron trolley guards available (except for 3 ton)
Lifetime warranty
Made in U.S.A.
$
588.72
Qty:
Part #:501580
- Key Features POWERSTATE™ Brushless Motor:
- Increased SPM and the power to cut hard materials, including hardwoods and metals REDLINK PLUS™ Intelligence
$
229.00
Qty:
closeout
$203.00 MSRP
$
144.21
Part #:507361
- CLOSEOUTS Only 2 Left!
- 11 Amp Corded 4-1/2 in. Small Angle Grinder Paddle No-Lock (Replaces discontinued 6140-30)
The 11 Amp 4-1/2 in. Small Angle Grinder (Paddle, Lock-On) delivers up to 3X more durability and up to 50% more power than the competition. With a 1,400 MWO motor that powers through the toughest jobs, the 6141-30 is the perfect match for industrial users. A grip circumference measuring a full 2 in. less than the competition, this Milwaukee grinder provides more control and less fatigue throughout the day. Featuring a 100% tool-free design, this Grinder allows the user to change all accessories, including hubbed product, without a wrench. In addition, the tool-free, burst resistant, adjustable guard allows users to make quick guard installations and adjustments.
Qty:
Part #:501847
- 8" 8/12 TPI SAWZALL® Blades (5 Pk)
Our Multi-Material SAWZALL® Blades can cut through a variety of materials in the toughest professional applications. This MILWAUKEE® reciprocating saw blade features double relief angles that reduce tooth stress for longer life and have our precision forming process to create sharper teeth for fast cutting in wood, nail embedded wood, composition material, plastic, cast iron, ferrous and non-ferrous metals. Each blade is equipped with matrix II bi-metal teeth for greater durability and a ½&rdquo universal tang that fits all SAWZALLS® for maximum versatility.
Qty:
Part #:800373
- The CM Puller is designed for heavy-duty construction and industrial
applications. Used to pull, lift, drag or stretch, it features Tough aluminum alloy construction
and powder coat finish
Weatherproof for outdoor service
Simple construction with fewer parts
for ease of maintenance and lower
inventories
Hoistaloy hardened steel link type
load chain for strength, long wear
life and flexibility
Weatherized Weston-type automatic
braking system for positive load
control
Easy, one-hand operation and
control only 58 pounds of pull
required for 34 ton model capacity
Forged upper and lower hooks with
latches standard
Free wheeling for fast and easy
attachment to load
Upper and lower Latchlok hooks
available for all capacities
Optional Load Limiter protection
device stops transmission of lever
forces protecting against dangerous
overload
Optional anchor sling simplifies
attachment to allow anchor
hook to swivel in tight space
applications (34 & 112 ton
units only)
Optional Load Sentry warns of
overload condition
Optional zinc-plated chain available
Unlimited lift
Lifetime warranty
Metric rated
Made in U.S.A.
$
1,005.72
Qty:
Part #:800375
- The CM Puller is designed for heavy-duty construction and industrial
applications. Used to pull, lift, drag or stretch, it features Tough aluminum alloy construction
and powder coat finish
Weatherproof for outdoor service
Simple construction with fewer parts
for ease of maintenance and lower
inventories
Hoistaloy hardened steel link type
load chain for strength, long wear
life and flexibility
Weatherized Weston-type automatic
braking system for positive load
control
Easy, one-hand operation and
control only 58 pounds of pull
required for 34 ton model capacity
Forged upper and lower hooks with
latches standard
Free wheeling for fast and easy
attachment to load
Upper and lower Latchlok hooks
available for all capacities
Optional Load Limiter protection
device stops transmission of lever
forces protecting against dangerous
overload
Optional anchor sling simplifies
attachment to allow anchor
hook to swivel in tight space
applications (34 & 112 ton
units only)
Optional Load Sentry warns of
overload condition
Optional zinc-plated chain available
Unlimited lift
Lifetime warranty
Metric rated
Made in U.S.A.
$
2,130.66
Qty:
Part #:512199
- M18 FUEL&trade w/ ONE-KEY&trade High Torque Impact Wrench 3/4" Friction Ring Bare Tool
The 2864&trade M18 FUEL&trade w/ ONE-KEY&trade High Torque 3/4&rdquo Impact Wrench with Friction Ring provides the Most Powerful, Most Compact, and the Most Repeatable Impact Wrench in the industry! The POWERSTATE&trade Brushless motor delivers up to 1,200ft-lbs of fastening torque and 1500ft-lbs of nut-busting torque, providing users a cordless solution that will eliminate the need for corded Impact Wrenches. The industry&rsquos most compact cordless High Torque Impact wrench at 8.59&rdquo in length, this tool allows for more access in tight spaces. REDLINK PLUS&trade intelligence prevents damage to the tool and battery due to overloading or overheating. REDLITHIUM&trade batteries deliver more work per charge and more work over the life of the battery. Compatible with ONE-KEY, this is the industry&rsquos first High Torque Impact Wrench that wirelessly connects to a smart phone to Customize, Track and Manage a tool&rsquos performance and location. Unlimited Tool Customization allows you to connect to the tool and access predetermined set-ups for specific fasteners and materials, or have complete control over output speed and power for the specific application at hand. With ONE-KEY&trade, users now have a tool that delivers the most repeatable torque output in the industry. Users looking for a targeted torque range now have solution that will get users close to their targeted torque value, reducing the likelihood of significant under or over torque. Users will experience less rework, less damage, and increased productivity that will get users closer to their torque target and will finish with a calibrated torque device to reach their targeted torque value. The tool&rsquos memory supports up to 4 custom profiles that can be easily accessed with the touch of a button on the tool. Once the profiles are saved to the tool, the connection to the smart phone is no longer necessary. Your custom profiles are also saved in the cloud so that they can be accessed at any time. Integrated Tool Tracking, also available through ONE-KEY&trade, provides full visibility to how and where tools are being used across your network of jobs and users. The app will track all ONE-KEY&trade compatible devices within 100 ft range of your phone. By building the functionality into the tool, not the battery, all devices are trackable even if the battery is not charged or on the tool. The app will automatically keep records of the last time a tool was within range of the app, allowing you to pinpoint missing tools quicker and increase accountability of your crew. If you&rsquore having trouble locating a lost tool, expand your search with the help of anybody with the ONE-KEY&trade app. By opting in, when any phone with the app comes within 100 ft of your tool, you will receive an updated location. Paired with tracking, Integrated Tool Security provides the ultimate theft protection. Protect your investment with features like tool lock-out, or hide tool from the nearby devices screen so only you can see your tool is in range. If your tool is lost or stolen, render it useless by sending a remote command to the tool to shut itself off the next time it comes within range of any ONE-KEY&trade app.
Up to 1500 ft-lbs Nut-Busting Torque
Most Compact
Most Repeatable Torque
POWERSTATE&trade brushless motor delivers up to 1200ft-lbs of fastening torque and 1500ft-lbs of nut-busting torque
Most compact cordless High Torque Impact Wrench in its class at 8.59" in length
ONE-KEY&trade Compatible Customize, Track and Manage tool&rsquos performance and location
M18 FUEL with ONEKEY&trade technology provides the most repeatable Impact Wrench in the industry
Easily toggle up to four custom performance profiles that can be saved to the memory of the tool
Features a friction ring with thru-hole design to ensure quick and easy socket changes
Premium rubber overmold withstands corrosive materials and provides increased comfort when in use
LED light to illuminate the work area
Part of the M18 System, featuring over 150+ tools
Qty:
Part #:800374
- The CM Puller is designed for heavy-duty construction and industrial
applications. Used to pull, lift, drag or stretch, it features Tough aluminum alloy construction
and powder coat finish
Weatherproof for outdoor service
Simple construction with fewer parts
for ease of maintenance and lower
inventories
Hoistaloy hardened steel link type
load chain for strength, long wear
life and flexibility
Weatherized Weston-type automatic
braking system for positive load
control
Easy, one-hand operation and
control only 58 pounds of pull
required for 34 ton model capacity
Forged upper and lower hooks with
latches standard
Free wheeling for fast and easy
attachment to load
Upper and lower Latchlok hooks
available for all capacities
Optional Load Limiter protection
device stops transmission of lever
forces protecting against dangerous
overload
Optional anchor sling simplifies
attachment to allow anchor
hook to swivel in tight space
applications (34 & 112 ton
units only)
Optional Load Sentry warns of
overload condition
Optional zinc-plated chain available
Unlimited lift
Lifetime warranty
Metric rated
Made in U.S.A.
$
1,497.46
Qty:
Part #:706624
- Inverted Bucket Steam TrapsEnergy efficient because it's so reliable The inverted bucket is the most reliable steam trap operating principle known. The heart of its simple design is a unique leverage system that multiplies the force provided by the bucket to open the valve against pressure. Since the bucket is open at the bottom, it resists damage from water hammer, and wear points are heavily reinforced for long life. The inverted bucket has only two moving parts-the valve lever assembly and the bucket. That means no fixed points, no complicated linkage. Nothing to stick, bind or clog. Conserves energy even in the presence of wear Armstrong inverted bucket steam traps open and close based on the difference in density between condensate and steam-the inverted bucket principle. They open and close gently, minimizing wear. This simple fact means that inverted buckets are subject to less wear than some other types of traps. In fact, as an Armstrong inverted bucket trap wears, its tight seal actually improves. The valve and seat of the Armstrong trap provide essentially line contact-resulting in a tight seal because the entire closing force is concentrated on one narrow seating ring. An Armstrong inverted bucket steam trap continues to operate efficiently with use. Gradual wear slightly increases the diameter of the seat and alters the shape and diameter of the valve. But, as this occurs, a tight seal is still preserved-the ball merely seats itself more deeply. Corrosion-resistant parts The stainless steel valve and seat of the Armstrong inverted bucket steam trap are individually ground and lapped together in matched sets. All other working parts are wear- and corrosion-resistant stainless steel. Venting of air and CO2 The Armstrong inverted bucket provides continuous automatic air and CO2 venting with no cooling lag or threat of air binding. Operation against back pressure The Armstrong inverted bucket has excellent performance against back pressure. It has no adverse effect on inverted bucket operation other than to reduce its capacity by the low differential. The bucket simply requires less force to pull the valve open and cycle the trap. Freedom from dirt problems Armstrong designed its inverted bucket to be virtually free of dirt problems. The valve and seat are at the top of the trap, far away from the larger particles of dirt, which fall to the bottom. Here, the up-and-down action of the bucket pulverizes them. Since the valve of an inverted bucket is either fully closed or open, dirt particles pass freely. And the swift flow of condensate from under the bucket's edge creates a unique self-scrubbing action that sweeps dirt out of the trap.
Qty:
Part #:706681
- Steam Trap ConnectorsBesides 2000 Series stainless steel inverted bucket traps, the standard 360° connector or IS-2 connector with integral strainer can also be used on many Armstrong thermostatic, disc, bimetallic, and float and thermostatic traps. Any manufacturer&rsquos two-bolt steam traps can use Armstrong connectors. IS-2 Stainless Steel Connector with Integral Strainer &bull A full line stainless steel strainer in the connector eliminates leak points and reduces installation time &bull A strainer that is not discarded when the trap is replaced &bull Easy strainer screen replacement &bull Optional blowdown valve &bull Accommodates Armstrong&rsquos inverted bucket, disc, thermostatic, thermostatic wafer, bimetallic, and float and thermostatic traps. Any manufacturer&rsquos 2-bolt steam trap can also be applied to Armstrong&rsquos S-2 connector. Standard 360° Stainless Steel Connector &bull A compact, lightweight assembly &bull Standardization, reducing inventory &bull A compact design, simplifying piping &bull Accommodates Armstrong&rsquos inverted bucket, disc, thermostatic, thermostatic wafer and bimetallic steam traps. Any manufacturer&rsquos 2-bolt steam trap can also be applied to Armstrong&rsquos standard connector.
Qty:
Part #:708464
- Steam Trap ConnectorsBesides 2000 Series stainless steel inverted bucket traps, the standard 360° connector or IS-2 connector with integral strainer can also be used on many Armstrong thermostatic, disc, bimetallic, and float and thermostatic traps. Any manufacturer&rsquos two-bolt steam traps can use Armstrong connectors. IS-2 Stainless Steel Connector with Integral Strainer &bull A full line stainless steel strainer in the connector eliminates leak points and reduces installation time &bull A strainer that is not discarded when the trap is replaced &bull Easy strainer screen replacement &bull Optional blowdown valve &bull Accommodates Armstrong&rsquos inverted bucket, disc, thermostatic, thermostatic wafer, bimetallic, and float and thermostatic traps. Any manufacturer&rsquos 2-bolt steam trap can also be applied to Armstrong&rsquos S-2 connector. Standard 360° Stainless Steel Connector &bull A compact, lightweight assembly &bull Standardization, reducing inventory &bull A compact design, simplifying piping &bull Accommodates Armstrong&rsquos inverted bucket, disc, thermostatic, thermostatic wafer and bimetallic steam traps. Any manufacturer&rsquos 2-bolt steam trap can also be applied to Armstrong&rsquos standard connector.
Qty:
Part #:713360
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:713363
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:713364
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:713365
Qty:
Part #:713366
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:801791
- SERIES 622
MODEL 622-A
1/2 TO 5 TON CAPACITIES
STANDARD LIFTS UP TO 30 FT.
HAND CHAIN HOIST. The CM Series 622 hand chain hoist features
a simple, efficient and economical design. With an ultra-low-headroom profile and lightweight steel construction, the CM 622 is easy to install, even in confined spaces. Redesigned for optimal performance, this hoist requires even less pull force for operation and has larger hook throat openings for easier attachment.
$
392.04
Qty:
Part #:521802
- The WRECKER&trade Multi-Material SAWZALL® Blade 12" 7/11TPI 5pk
The Next Generation Wrecker is designed for Multi-Material demolition cutting. This means it has the capability of cutting nail, embedded wood, plastics and a variety of metals. This blade has 25% more high speed steel for increased life and durability. With all of these features, the Next Generation Wrecker is a true demolition blade for the professional user.
Qty:
closeout
$
421.92
Qty:
Qty:
Part #:514131
- 14 TPI Standard Deep Cut Portable Band Saw Blade 1PK
Maximize your band saw performance and make straight, accurate cuts in a variety of materials with the Milwaukee® 14 TPI Standard / Deep-Cut Portable Band Saw Blade. Get exceptional durability and accuracy for your portable band saw that takes a 44-7/8" blade. Milwaukee's standard/deep cut band saw blades deliver long tooth life in a variety of metal, including strut, conduit, angle iron, copper tube, threaded rod and pipe. The blade's tooth form, pitch and set ensure straight, accurate cuts time and time again.
Qty:
Displaying: 1 - 24 of 2,154 Matching Items