Dixon Valve & Coupling Company Llc
Armstrong International
View:
Active Filters :
Part #:713360
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:713363
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:713364
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:713365
Qty:
Part #:713366
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Qty:
Qty:
Qty:
Part #:334-2721212C
- Male NPT x Push-on Hose Barb Attributes
Weight
0.194 lb
Material
Brass
Component Material
Yellow Plastic Cap
Male Thread
NPTF
Temperature Range
-40°F to 150°F
Length
2.55"
Hose ID
3/4"
Hex
1-1/16"
Male Thread Size
3/4"-14
Pressure Rating
350 PSI
$
6.38
Qty:
Part #:104403
- Conical Muffler Attributes
Maximum Operating Pressure
300 PSI
Weight
0.0355 lb
Material
Nickel Plated Steel
Male Thread
NPT
Temperature Range
35°F to 300°F (1.7°C to 149°C)
Length
1-3/8"
Male Thread Size
1/4"
$
2.67
Qty:
Part #:100696
- SSE31 - Stretch Strap
Attributes
Weight
0.36 lb
Break Quantity
0
Optional Package/Box Quantity
0
Length
31"
$
3.06
Qty:
Part #:713381
- Float and Thermostatic (F&T) Steam TrapsThe More Your Steam Pressure Varies, The More You Need Armstrong F&T TrapsWhen steam pressure may vary from maximum steam supply pressure to vacuum, Armstrong F&Ts are your most energy-efficient choice. Our line of F&Ts brings Armstrong performance, dependability and long life to trapping services requiring continuous drainage with high air venting capacity. Thanks to separate orifices for condensate and air, they provide continuous condensate drainage and air venting-even under conditions of zero pressure. All the benefits detailed here have been designed into Armstrong F&Ts through long experience in the manufacture of pressure float-type traps. They assure you of optimum operating efficiency for long periods with minimum trouble. How they work Float and thermostatic traps are mechanical units that operate on both density and temperature principles. The float valve operates on the density principle. A level connects the ball float to the valve and seat. Once condensate reaches a certain level in the trap, the float rises, opening the orifice and draining condensate. A water seal formed by the condensate prevents live steam loss. Since the discharge valve is under water, it is not capable of venting air and non-condensables. When the accumulation of air and con-condensable gases causes a significant temperature drop, a thermostatic air vent in the top of the trap discharges them. The thermostatic vent opens at a temperature a few degrees below saturation, so it's able to handle a large volume of air-through an entirely separate orifice-but at a slightly reduced temperature. Built as tough as the jobs they do Armstrong float and thermostatic traps are unique in their super heavy duty construction. Armstrong uses high quality ASTM A48 Class 30 cast iron or ASTM A216 WCB cast steel-normally found in pressure vessels rated to 250 psi (17 bar) or 465 psi (32 bar). Internal mechanisms are made from stainless steel and are heavily reinforced. No brass cotter pins here. Valves and seats are stainless steel, hardened, ground and lapped to withstand the erosive forces of flashing condensate. Why go to all this trouble for traps normally recommended for low-pressure, modulating service? The operative word here is modulating. Modulating pressures mean widely varying loads, thermal cycling and high air and non-condensable gas loads. In other words tough service. Inferior, lightweight construction in this kind of service is a mistake waiting to happen. Trap failures on modulating pressure may lead to water hammer, corrosion and even damage to heat exchangers. Armstrong's published capacities are based on actual measurements of traps handling hot, flashing condensate. Competitive F&Ts may utilize theoretical calculated capacities. Armstrong uses its own steam lab to give you actual capacity-especially important on high-capacity traps such as those in our ultra-capacity line. Not only does Armstrong offer super heavy duty construction for long life and reliability, but we also supply the data to back up performance. Here's a simple, easy-to-remember summary The more your pressure varies, the more you need Armstrong F&Ts.
Qty:
Part #:509866
-
TE-YX FM Flat chisels Narrow-Flat Chisel TE-YP FM 28 #2241990
Connection endTE-Y (SDS Max)Length11 inWidth1 inProduct ClassUltimate
$
69.89
Qty:
Part #:505194
- Kwik Bolt 1 carbon steel wedge anchor
High-performance wedge anchor for cracked concrete and seismic (carbon steel)
Material, corrosionCarbon steel, zinc-plated
Head configurationExternally threaded
Drilling Method (AS)Hammer Drilling, Hollow Drill Bit Drilling
Material, corrosionCarbon steel, zinc-platedHead configurationExternally threadedDrilling Method (AS)Hammer Drilling, Hollow Drill Bit DrillingInstallation toolsTE 6-A36 Cordless rotary hammer, SIW 6AT-A22 Cordless impact wrench
$
1.39
Qty:
Part #:500704
- Kwik Bolt 1 carbon steel wedge anchor
High-performance wedge anchor for cracked concrete and seismic (carbon steel)
Material, corrosionCarbon steel, zinc-plated
Head configurationExternally threaded
Drilling Method (AS)Hammer Drilling, Hollow Drill Bit Drilling
Material, corrosionCarbon steel, zinc-platedHead configurationExternally threadedDrilling Method (AS)Hammer Drilling, Hollow Drill Bit DrillingInstallation toolsTE 6-A36 Cordless rotary hammer, SIW 6AT-A22 Cordless impact wrench
$
6.71
Qty:
closeout
$23.00 MSRP
$
15.01
Part #:504774
- CLOSEOUTS Only 1 Left!
- 1/2" Drive 6-Point SAE 1-1/8" Shallow Socket &bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener &bull Designed for maximum engagement on 6 point fasteners
Qty:
Part #:841-681-36080
- L.S. Starrett Angle MetersProduct DetailsMagnetic base frees hands when used on ferrous surfacesMeasures any angle for pitch or slopeHandy rise, run, angle, and pitch information on back of toolLarge, readable scale for accurate readings from 0-90° in any quadrant
Qty:
Part #:800931
-
art Number
5141212C
Material
CDA Brass 360
Female Thread
NPTF
Female Thread Size
1/2"-14
Male Thread
GHT x NPTF
Male Thread Size
3/4"-11-1/2 x 3/4"-14
Hex
1-1/16"
Length
1.50"
Weight Lb
0.1600
$
4.62
Qty:
Part #:500250
-
TE 2 Rotary hammer Rotary hammer perf pkg TE 2 #3497789
Compact dual-mode, pistol-grip SDS Plus (TE-C) rotary hammer &ndash for hammer drilling and rotary-only drilling
Weight according EPTA-Procedure 01/20036 lb.
Working modeHammer drilling, Drilling
Hammer drilling diameter range5/32 - 7/8 in
Kit Contains
TE 2 120V Rotary Hammer
TE 2 Tool Case
Chuck Grease
Hammer Drill Bit TE-CX 3/8"x6"
Hammer Drill Bit TE-CX 1/4"x6"
Hammer Drill Bit TE-CX 3/16"x6"
Weight according EPTA-Procedure 01/20036 lb.Working modeHammer drilling, DrillingHammer drilling diameter range5/32 - 7/8 inOptimum Hammer drilling range5/32 - 15/32 inSingle impact energy1.3 ft-lbsHammer drilling RPM1200 rpmFull hammering frequency4600 impacts/minuteFunctionalityReverse mode, Depth gaugeTriaxial vibration value for hammer drilling into concrete (ah,HD)13.5 m/s² 1 A-weighted emission sound pressure level91 dB (A) 2 Dimensions (LxWxH)13.9 x 3.5 x 8 mm
$
397.70
Qty:
Part #:508560
-
X-U P8 Steel/concrete nails Universal nail X-U 37 P8 #2141088
Ultimate-performance single nail for fastening to concrete and steel using powder-actuated tools
Base materialsConcrete (soft), Concrete (tough), Steel, Masonry (solid limestone brick)
Minimum thickness of base material (concrete)80 mm
Minimum thickness of base material (steel)1/4 in
Corrosion protectionGalvanized zinc coatedEnvironmental ConditionsDry indoorMaterialCarbon steelFastener shank diameter0.16 inWasher size5/16 inPoint typeBallistic point, knurledApprovalsABS, COLA, DIBt, IBMB, ICC-ES, LRFor use with (tools)DX 2, DX 35, DX 351, DX 351 M/E, DX 36, DX 460 F8, DX 462 F8, DX 5 F8, DX E72Product ClassUltimate
Part #:508562
-
X-U P8 Steel/concrete nails Universal nail X-U 47 P8 #2141180
Base materialsConcrete (soft), Concrete (tough), Steel, Masonry (solid limestone brick)Minimum thickness of base material (concrete)80 mmMinimum thickness of base material (steel)1/4 inCorrosion protectionGalvanized zinc coatedEnvironmental ConditionsDry indoorMaterialCarbon steelFastener shank diameter0.16 inWasher size5/16 inPoint typeBallistic point, knurledApprovalsABS, COLA, DIBt, IBMB, ICC-ES, LRFor use with (tools)DX 2, DX 36, DX 460 F8, DX 5 F8, DX E72Product ClassUltimate
Part #:508567
-
X-U P8 Steel/concrete nails Universal nail X-U 19 P8 #2141084Base materialsSteelMinimum thickness of base material (concrete)80 mmMinimum thickness of base material (steel)1/4 inCorrosion protectionGalvanized zinc coated <20 µmEnvironmental ConditionsDry indoorMaterialCarbon steelFastener shank diameter0.16 inWasher size5/16 inPoint typeBallistic point, knurledApprovalsABS, COLA, DIBt, IBMB, ICC-ES, LRFor use with (tools)DX 2, DX 35, DX 351, DX 351 M/E, DX 36, DX 460 F8, DX 462 F8, DX 5 F8, DX E72Product ClassUltimate
Part #:508626
-
HDI+ / HDI Flush anchor Drop-in anchor HDI 5/8" #336428Approvals / Test reportsFM (Factory Mutual), UL (Underwriter Laboratories)Material, corrosionCarbon steel, zinc-platedBase materialsConcrete (lightweight), Concrete (lightweight over metal deck), Concrete (uncracked)PROFIS SoftwareNoDrill bit diameter27/32 inProduct ClassPremium
Part #:509862
-
Adapter TE-Y to TE-C+ #74068
Chuck
Accessory typeChuck
Chuck typeClick chuck
Product informationAllows a TE-C (SDS-plus) chuck to be fitted to a TE-Y (SDS-max) power tool
Accessory typeChuckChuck typeClick chuckProduct informationAllows a TE-C (SDS-plus) chuck to be fitted to a TE-Y (SDS-max) power toolAdditional Accessory InformationAllows a TE-C (SDS-plus) chuck to be fitted to a TE-Y (SDS-max) power tool
$
381.94
Qty:
Displaying: 25 - 48 of 2,441 Matching Items