Imark/edn Greenlee Textron
Armstrong International
View:
Active Filters :
Part #:301702
- Stem Mount Thermal Photocontrol, 120 V
These photocontrols install on standard outdoor light fixtures and electrical boxes with 1&frasl2"-14 NPSM thread or 7&frasl8" knock-out holes for dusk-to-dawn ON/OFF control of outdoor lighting.
$
15.35
Qty:
Part #:305991
- Locking Type Thermal Photocontrol, 120-277 V
These photocontrols install on light fixtures with ANSI C136.10 NEMA receptacles commonly found on street light fixtures. Locking type design facilitates fast installation and replacement of photocontrol.
$
24.41
Qty:
Part #:506147
- Hand-Held Cable Cutter
Easily cuts heavier copper and aluminum cables up to 2/0 (70 mm²)
Precision-ground, shear-action, curved cutting blades
727 has PVC-covered, high-leverage handles for easier cuts
Heat-treated for long life
Made of heavy-duty forged steel
Rust-resistant black oxide finish
$
39.05
Qty:
Part #:706624
- Inverted Bucket Steam TrapsEnergy efficient because it's so reliable The inverted bucket is the most reliable steam trap operating principle known. The heart of its simple design is a unique leverage system that multiplies the force provided by the bucket to open the valve against pressure. Since the bucket is open at the bottom, it resists damage from water hammer, and wear points are heavily reinforced for long life. The inverted bucket has only two moving parts-the valve lever assembly and the bucket. That means no fixed points, no complicated linkage. Nothing to stick, bind or clog. Conserves energy even in the presence of wear Armstrong inverted bucket steam traps open and close based on the difference in density between condensate and steam-the inverted bucket principle. They open and close gently, minimizing wear. This simple fact means that inverted buckets are subject to less wear than some other types of traps. In fact, as an Armstrong inverted bucket trap wears, its tight seal actually improves. The valve and seat of the Armstrong trap provide essentially line contact-resulting in a tight seal because the entire closing force is concentrated on one narrow seating ring. An Armstrong inverted bucket steam trap continues to operate efficiently with use. Gradual wear slightly increases the diameter of the seat and alters the shape and diameter of the valve. But, as this occurs, a tight seal is still preserved-the ball merely seats itself more deeply. Corrosion-resistant parts The stainless steel valve and seat of the Armstrong inverted bucket steam trap are individually ground and lapped together in matched sets. All other working parts are wear- and corrosion-resistant stainless steel. Venting of air and CO2 The Armstrong inverted bucket provides continuous automatic air and CO2 venting with no cooling lag or threat of air binding. Operation against back pressure The Armstrong inverted bucket has excellent performance against back pressure. It has no adverse effect on inverted bucket operation other than to reduce its capacity by the low differential. The bucket simply requires less force to pull the valve open and cycle the trap. Freedom from dirt problems Armstrong designed its inverted bucket to be virtually free of dirt problems. The valve and seat are at the top of the trap, far away from the larger particles of dirt, which fall to the bottom. Here, the up-and-down action of the bucket pulverizes them. Since the valve of an inverted bucket is either fully closed or open, dirt particles pass freely. And the swift flow of condensate from under the bucket's edge creates a unique self-scrubbing action that sweeps dirt out of the trap.
Qty:
Part #:706681
- Steam Trap ConnectorsBesides 2000 Series stainless steel inverted bucket traps, the standard 360° connector or IS-2 connector with integral strainer can also be used on many Armstrong thermostatic, disc, bimetallic, and float and thermostatic traps. Any manufacturer&rsquos two-bolt steam traps can use Armstrong connectors. IS-2 Stainless Steel Connector with Integral Strainer &bull A full line stainless steel strainer in the connector eliminates leak points and reduces installation time &bull A strainer that is not discarded when the trap is replaced &bull Easy strainer screen replacement &bull Optional blowdown valve &bull Accommodates Armstrong&rsquos inverted bucket, disc, thermostatic, thermostatic wafer, bimetallic, and float and thermostatic traps. Any manufacturer&rsquos 2-bolt steam trap can also be applied to Armstrong&rsquos S-2 connector. Standard 360° Stainless Steel Connector &bull A compact, lightweight assembly &bull Standardization, reducing inventory &bull A compact design, simplifying piping &bull Accommodates Armstrong&rsquos inverted bucket, disc, thermostatic, thermostatic wafer and bimetallic steam traps. Any manufacturer&rsquos 2-bolt steam trap can also be applied to Armstrong&rsquos standard connector.
Qty:
Part #:708464
- Steam Trap ConnectorsBesides 2000 Series stainless steel inverted bucket traps, the standard 360° connector or IS-2 connector with integral strainer can also be used on many Armstrong thermostatic, disc, bimetallic, and float and thermostatic traps. Any manufacturer&rsquos two-bolt steam traps can use Armstrong connectors. IS-2 Stainless Steel Connector with Integral Strainer &bull A full line stainless steel strainer in the connector eliminates leak points and reduces installation time &bull A strainer that is not discarded when the trap is replaced &bull Easy strainer screen replacement &bull Optional blowdown valve &bull Accommodates Armstrong&rsquos inverted bucket, disc, thermostatic, thermostatic wafer, bimetallic, and float and thermostatic traps. Any manufacturer&rsquos 2-bolt steam trap can also be applied to Armstrong&rsquos S-2 connector. Standard 360° Stainless Steel Connector &bull A compact, lightweight assembly &bull Standardization, reducing inventory &bull A compact design, simplifying piping &bull Accommodates Armstrong&rsquos inverted bucket, disc, thermostatic, thermostatic wafer and bimetallic steam traps. Any manufacturer&rsquos 2-bolt steam trap can also be applied to Armstrong&rsquos standard connector.
Qty:
Part #:307241
- NightFox&trade Stem Mount Electronic Photocontrol, 120-277 V
NightFox&trade electronic photocontrols permanently install on outdoor electrical boxes or outdoor lighting fixtures. Ideal for LED fixtures with long-life expectations. ½&rdquo-14 NPSM threaded stem fits standard outlet boxes and wall packs with a minimum installation hole size of 7/8&rdquo diameter. Come with 9" wire leads.
$
22.40
Qty:
Part #:309367
- NightFox&trade Select Grade Locking Type Electronic Photocontrol, 120-277 V
Designed to meet a 15-year service life, this photocontrol is LED-compatible and backed by an 8-year warranty.
$
17.96
Qty:
Part #:713360
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:713363
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:713364
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:713365
Qty:
Part #:713366
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:300423
- Wall Mount Thermal Photocontrol, 120 V
Intermatic&rsquos wall mount thermal-type photocontrol installs into standard outdoor single-gang electrical boxes. The photocontrol provides dusk-to-dawn lighting control. Compatible with Fluorescent, HID, and Incandescent bulbs.
$
16.96
Qty:
Part #:309735
- NightFox&trade Stem and Swivel Mount Electronic Photocontrol, 120-277 V
NightFox&trade electronic photocontrols permanently install on outdoor electrical boxes or outdoor lighting fixtures. Ideal for LED fixtures with long-life expectations. ½&rdquo-14 NPSM threaded stem fits standard outlet boxes and wall packs with a minimum installation hole size of 7/8&rdquo diameter. Come with 9" wire leads.
$
24.48
Qty:
Part #:500591
- 7/8" Step Bit (#7)
Durable split-point tip for fast, accuratematerialpenetration.
Patented split-step design optimizes chip load for fast, smooth cutting,and moreholes percharge.
Progressive cutting edges provide balanced aggression to maximizetorqueefficiency and minimize stalling.
Improved double flute design for superior chip evacuation, cuttingspeeds and tool life.
Three-flat shank for all 1/2&rdquo drill chucks.
Laser markings for quick, easy product and size identification.
Replaced 34411
$
59.90
Qty:
Part #:802874
- SCREW UNIT,DRIVE
Replacement Manual Draw Stud Packaged
$
36.15
Qty:
Part #:807974
- 11/16 x 18 Nail Eater® Bit
Improved cutting edge provides 30% longer life span
Patented new design for improved cutting and cleaner holes
Self-feeding screw point draws bit through wood
Unique patented design cutting angle - smoother starts, reduced cutting loads
Made of super tough, heat-treated steel
Cuts through nails and provides longer life
Shorty bits - for working in tight places, yet still can go through three abutting 2 x 4s
See Bit Extensionsif more length is required
P.O.P packaged
$
34.45
Qty:
Part #:803761
- 3/4 x 18 Nail Eater® Bit
Improved cutting edge provides 30% longer life span
Patented new design for improved cutting and cleaner holes
Self-feeding screw point draws bit through wood
Unique patented design cutting angle - smoother starts, reduced cutting loads
Made of super tough, heat-treated steel
Cuts through nails and provides longer life
Shorty bits - for working in tight places, yet still can go through three abutting 2 x 4s
See Bit Extensionsif more length is required
P.O.P packaged
$
33.10
Qty:
Part #:803767
- 7/8 x 18 Nail Eater® Bit
Improved cutting edge provides 30% longer life span
Patented new design for improved cutting and cleaner holes
Self-feeding screw point draws bit through wood
Unique patented design cutting angle - smoother starts, reduced cutting loads
Made of super tough, heat-treated steel
Cuts through nails and provides longer life
Shorty bits - for working in tight places, yet still can go through three abutting 2 x 4s
See Bit Extensionsif more length is required
P.O.P packaged
$
37.85
Qty:
Part #:305664
- Round Conduit Die - 3/4"
Made in the USA
Replacement Die 3/4" Conduit for Standard Round Knockout Punches
Alignment Markings improve punching accuracy and productivity when making holes.
Punches and dies are marked with catalog numbers and sizes for quick part identification.
$
20.25
Qty:
Part #:512710
- 6-32 to 1/4-20 6-Piece Drill Tap Set
Complete hole drilling, tapping and deburring/countersinking in one operation using power drill to save time and labor
Back tapered beyond tap to prevent thread damage from over-drilling
Power tool accessory made from hardened high-speed steel versus carbon-steel for longer life
High quality hex shank to ensure strong connection to drill chuck
Designed to tap up to 10 gauge metal
Quick change adaptor included
$
50.00
Qty:
Part #:811000
- Pro Stainless Wire Stripper / Cutter / Crimper
High grade stainless steel lasts 5X longer
Precision ground stripping holes offer easy, consistent jacket removal
Strips 10-18 AWG Solid and12-20 AWG Stranded conductors
Cleanly shears 6-32 and 8-32 bolts
Crimps 16-10 insulated and non-insulated terminals
Multiple functions include plier nose, strippers, cutter, looping holes, crimper, bolt re-thread/shear and spring back with low profile lock
Looping holes and serrated nose for bending, pulling and shaping wires
Long-life spring and low-profile lock for quick, repetitive stripping and cutting
Vinyl cushion grip resists slipping and has an ergonomic fit
$
24.65
Qty:
$
41.35
Qty:
Displaying: 1 - 24 of 2,144 Matching Items