Core and Main
Armstrong International
View:
Active Filters :
- Brand: Armstrong International Core and Main Parker
- Size: 3/4in x 1/2in 8in
Qty:
Qty:
Part #:203866
- Socket Clamps Pipe OD 9.05in, 5/8in-11 x 3in Bolt Size, Stock Size 1/2in x 2in,
For use in preventing underground pipe joints from separating
Also known as &ldquoRetainer Clamps&rdquo or &ldquoFriction Clamps&rdquo. Designed for centrifugally-spun cast and ductile iron pipe with OD&rsquos as shown in the table below.
All Socket Clamps include two half clamps, two bolts and nuts and two washers. Sizes 3&Prime through 12&Prime are supplied with #585 cast washers, which are shown below as replacement parts. Sizes 14&Prime and larger are supplied with two fabricated washers.
Used with all-thread rod and Trumbull tie-lugs or tie-bolts for joint restraint, shown
$
84.75
Qty:
Qty:
Part #:501-C3510-10
Qty:
Part #:501-C3510-4
Qty:
Part #:501-C3510-5
Qty:
Part #:501-D27091
- AEH Series Exhaust Heads Armstrongs AEH series carbon steel exhaust heads should be used when there is a risk of water carryover up an atmospheric vent pipe. The internal knock-out plate and stainless steel mesh screening effectively contains water carry-over and discharges it through the bottom drain leaving dry flash steam to vent through the top of the vessel.
Connections
• Flanged ASME B16.5 CL 150
• Drain FNPT
Qty:
Part #:501-D39126
- DS Series In-Line Condensate SeparatorsCarbon Steel Drain SeparatorCondensate in steam and air piping reduces thermal efficiency, causes water hammer, corrodes equipment such as valves and pipes, and causes other problems.
In-line (drain) separators DS-1, DS-2, DS-3, and DS-4 separate condensate efficiently by using the centrifugal force of steam or air created by introducing it into a specifically shaped path. Because of the simple structure of the drain separators, pressure loss is minimized, enabling clean, dry steam or air to be fed to equipment.
When steam or air flow enters the drain separator, centrifugal force is generated in the fluid because of the devices internal structural design. The fluid drains along the wall because of the difference in specific gravity with steam or air, eventually striking the baffle. The baffle guides the fluid to the drain outlet and to the trap, which drains it. As a result, small dirt particles and condensate are separated and removed from the system through the bottom drain.
• Cyclone structure maximizes liquid separation efficiency
• Pressure loss is extremely low
• No moving parts means no breakdowns
Qty:
Part #:501-D39127
- DS Series In-Line Condensate SeparatorsCarbon Steel Drain SeparatorCondensate in steam and air piping reduces thermal efficiency, causes water hammer, corrodes equipment such as valves and pipes, and causes other problems.
In-line (drain) separators DS-1, DS-2, DS-3, and DS-4 separate condensate efficiently by using the centrifugal force of steam or air created by introducing it into a specifically shaped path. Because of the simple structure of the drain separators, pressure loss is minimized, enabling clean, dry steam or air to be fed to equipment.
When steam or air flow enters the drain separator, centrifugal force is generated in the fluid because of the devices internal structural design. The fluid drains along the wall because of the difference in specific gravity with steam or air, eventually striking the baffle. The baffle guides the fluid to the drain outlet and to the trap, which drains it. As a result, small dirt particles and condensate are separated and removed from the system through the bottom drain.
• Cyclone structure maximizes liquid separation efficiency
• Pressure loss is extremely low
• No moving parts means no breakdowns
Qty:
Part #:501-D500010
Qty:
Part #:501-D500068
Qty:
Part #:501-D502707
Qty:
Part #:501-D502875
Qty:
Part #:501-D503037
Qty:
Part #:501-D509466
Qty:
Part #:501-D537850
Qty:
Part #:501-D549579
Qty:
Part #:1128-12-8 F6X-S
- Performance Characteristics
Connection Type
37° Flare
Industry Standards
SAE J514
Maximum Dynamic Pressure (psi)
5000
Shape
Straight
Connection Style
Tube to NPT
Connection 1 Style
Female 37° Flare Swivel
Connection 1 Tube O.D. (inch)
3/4
Connection 1 Tube O.D. (mm)
18, 20
Connection 2 Style
Male NPT/NPTF
Connection 2 Tube O.D. (inch)
na
Connection 2 Tube O.D. (mm)
na
Connection 2 Thread Size (inch)
1/2-14
Connection 2 Thread Size (mm)
na
Connection 3 Style
na
Connection 3 Tube O.D. (inch)
na
Connection 3 Tube O.D. (mm)
na
Connection 3 Thread Size (inch)
na
Connection 3 Thread Size (mm)
na
Connection 4 Style
na
Connection 4 Tube O.D. (inch)
na
Connection 4 Tube O.D. (mm)
na
O-Ring Material
na
Body Material
Steel, Chromium-6 Free
$
9.20
Qty:
Part #:1128-12-8 FTX-S
- Performance Characteristics
Connection Type
37° Flare
Industry Standards
SAE J514
Maximum Dynamic Pressure (psi)
5000
Shape
Straight
Connection Style
Tube to NPT
Connection 1 Style
Male 37° Flare
Connection 1 Tube O.D. (inch)
3/4
Connection 1 Tube O.D. (mm)
18, 20
Connection 2 Style
Male NPT/NPTF
Connection 2 Tube O.D. (inch)
na
Connection 2 Tube O.D. (mm)
na
Connection 2 Thread Size (inch)
1/2-14
Connection 2 Thread Size (mm)
na
Connection 3 Style
na
Connection 3 Tube O.D. (inch)
na
Connection 3 Tube O.D. (mm)
na
Connection 3 Thread Size (inch)
na
Connection 3 Thread Size (mm)
na
Connection 4 Style
na
Connection 4 Tube O.D. (inch)
na
Connection 4 Tube O.D. (mm)
na
O-Ring Material
na
Body Material
Steel, Chromium-6 Free
$
3.65
Qty:
Part #:735103
- Armstrong 11AV 3/4in NPT x 1/2in NPT Outlet with 1/8in Orifice 178lb Stainless Steel, Air Vent, Bottom Inlet - Top Outlet C3510-3
Qty:
Part #:563465
Qty:
Displaying: 1 - 22 of 22 Matching Items