Cantex
Armstrong International
View:
Active Filters :
Part #:502787
- Brute Vented Trash Receptacle, Round, 44 gal, Gray
Rounded handles make lifting and moving easier, and are reinforced to resist tearing or damage from even the heaviest loads.
Reinforced base is specifically engineered to be dragged over rough surfaces, extending life and overall durability even in the toughest environments.
Colors complement your facility's recycling, sortation, and organization needs.
Seamless construction makes cleaning the container easier.
Stackable design enables nesting for easy transport and storage.
Qty:
Part #:706624
- Inverted Bucket Steam TrapsEnergy efficient because it's so reliable The inverted bucket is the most reliable steam trap operating principle known. The heart of its simple design is a unique leverage system that multiplies the force provided by the bucket to open the valve against pressure. Since the bucket is open at the bottom, it resists damage from water hammer, and wear points are heavily reinforced for long life. The inverted bucket has only two moving parts-the valve lever assembly and the bucket. That means no fixed points, no complicated linkage. Nothing to stick, bind or clog. Conserves energy even in the presence of wear Armstrong inverted bucket steam traps open and close based on the difference in density between condensate and steam-the inverted bucket principle. They open and close gently, minimizing wear. This simple fact means that inverted buckets are subject to less wear than some other types of traps. In fact, as an Armstrong inverted bucket trap wears, its tight seal actually improves. The valve and seat of the Armstrong trap provide essentially line contact-resulting in a tight seal because the entire closing force is concentrated on one narrow seating ring. An Armstrong inverted bucket steam trap continues to operate efficiently with use. Gradual wear slightly increases the diameter of the seat and alters the shape and diameter of the valve. But, as this occurs, a tight seal is still preserved-the ball merely seats itself more deeply. Corrosion-resistant parts The stainless steel valve and seat of the Armstrong inverted bucket steam trap are individually ground and lapped together in matched sets. All other working parts are wear- and corrosion-resistant stainless steel. Venting of air and CO2 The Armstrong inverted bucket provides continuous automatic air and CO2 venting with no cooling lag or threat of air binding. Operation against back pressure The Armstrong inverted bucket has excellent performance against back pressure. It has no adverse effect on inverted bucket operation other than to reduce its capacity by the low differential. The bucket simply requires less force to pull the valve open and cycle the trap. Freedom from dirt problems Armstrong designed its inverted bucket to be virtually free of dirt problems. The valve and seat are at the top of the trap, far away from the larger particles of dirt, which fall to the bottom. Here, the up-and-down action of the bucket pulverizes them. Since the valve of an inverted bucket is either fully closed or open, dirt particles pass freely. And the swift flow of condensate from under the bucket's edge creates a unique self-scrubbing action that sweeps dirt out of the trap.
Qty:
Part #:706681
- Steam Trap ConnectorsBesides 2000 Series stainless steel inverted bucket traps, the standard 360° connector or IS-2 connector with integral strainer can also be used on many Armstrong thermostatic, disc, bimetallic, and float and thermostatic traps. Any manufacturer&rsquos two-bolt steam traps can use Armstrong connectors. IS-2 Stainless Steel Connector with Integral Strainer &bull A full line stainless steel strainer in the connector eliminates leak points and reduces installation time &bull A strainer that is not discarded when the trap is replaced &bull Easy strainer screen replacement &bull Optional blowdown valve &bull Accommodates Armstrong&rsquos inverted bucket, disc, thermostatic, thermostatic wafer, bimetallic, and float and thermostatic traps. Any manufacturer&rsquos 2-bolt steam trap can also be applied to Armstrong&rsquos S-2 connector. Standard 360° Stainless Steel Connector &bull A compact, lightweight assembly &bull Standardization, reducing inventory &bull A compact design, simplifying piping &bull Accommodates Armstrong&rsquos inverted bucket, disc, thermostatic, thermostatic wafer and bimetallic steam traps. Any manufacturer&rsquos 2-bolt steam trap can also be applied to Armstrong&rsquos standard connector.
Qty:
Part #:708464
- Steam Trap ConnectorsBesides 2000 Series stainless steel inverted bucket traps, the standard 360° connector or IS-2 connector with integral strainer can also be used on many Armstrong thermostatic, disc, bimetallic, and float and thermostatic traps. Any manufacturer&rsquos two-bolt steam traps can use Armstrong connectors. IS-2 Stainless Steel Connector with Integral Strainer &bull A full line stainless steel strainer in the connector eliminates leak points and reduces installation time &bull A strainer that is not discarded when the trap is replaced &bull Easy strainer screen replacement &bull Optional blowdown valve &bull Accommodates Armstrong&rsquos inverted bucket, disc, thermostatic, thermostatic wafer, bimetallic, and float and thermostatic traps. Any manufacturer&rsquos 2-bolt steam trap can also be applied to Armstrong&rsquos S-2 connector. Standard 360° Stainless Steel Connector &bull A compact, lightweight assembly &bull Standardization, reducing inventory &bull A compact design, simplifying piping &bull Accommodates Armstrong&rsquos inverted bucket, disc, thermostatic, thermostatic wafer and bimetallic steam traps. Any manufacturer&rsquos 2-bolt steam trap can also be applied to Armstrong&rsquos standard connector.
Qty:
Part #:300016
- Description CANTEX 5133736 is a 1/2 in. Conduit Clamp / Strap which is a U-shaped conduit support used to anchor conduit to interior or exterior surfaces Features Two holes in the feet of the clamp allow mounting the screws or nails Durable non-conductive PVC will not rust or corrode For use with Schedule 40 & 80 conduit UL and CSA listed Made in USA Requires two #10 screws for installation (not included)
$
0.22
Qty:
Part #:301272
- CANTEX 6141625 is a 1 in. Schedule 40 Standard Center Stop Coupling used to join lengths of conduit pipe together with two solvent weld socket ends
Features
For use with Schedule 40 and Schedule 80 conduit. May also be used in EB & DB Duct applications.
Center stop to help determine proper depth of connection
For use aboveground and underground and non-conductive and sunlight resistant
Meets NEMA TC-3 Standards
UL and CSA listed
Made in USA
$
0.21
Qty:
Part #:301354
- CANTEX 6141630 is a 3 in. Schedule 40 Standard Center Stop Coupling used to join lengths of conduit pipe together with two solvent weld socket ends
Features
For use with Schedule 40 and Schedule 80 conduit. May also be used in EB & DB Duct applications.
Center stop to help determine proper depth of connection
For use aboveground and underground and non-conductive and sunlight resistant
Meets NEMA TC-3 Standards
UL and CSA listed
Made in USA
$
1.43
Qty:
Part #:301356
- CANTEX 6141632 is a 4 in. Schedule 40 Standard Center Stop Coupling used to join lengths of conduit pipe together with two solvent weld socket ends
Features
For use with Schedule 40 and Schedule 80 conduit. May also be used in EB & DB Duct applications.
Center stop to help determine proper depth of connection
For use aboveground and underground and non-conductive and sunlight resistant
Meets NEMA TC-3 Standards
UL and CSA listed
Made in USA
$
2.20
Qty:
Part #:301402
- CANTEX 5140112 is a 4 in. Male Terminal Adapter which is a connector used to transition from a spigot end PVC conduit to a threaded metal or PVC plastic female bell end
Features
Durable non-conductive PVC will not rust or corrode
For use with Schedule 40 and Schedule 80 conduit. May also be used in EB & DB Duct applications.
Meets NEMA TC-3 Standards
UL and CSA listed
Made in USA
$
3.02
Qty:
Part #:301405
- CANTEX 5133828 is a 2 in. x 90-Degree Plain End Schedule 40 Standard Radius Elbow used to change the direction of a conduit run by 90-Degree
Features
Schedule 40 Nonmetallic PVC construction for strength and durability
For indoor or outdoor use
Suitable for aboveground or buried
Plain-end connections are solvent weld
ETL listed Conforms to UL 651 and NEMA TC-3 Conforms to UL 651 and NEMA TC-3
Made in USA
$
2.09
Qty:
Part #:301414
- CANTEX 5133832 is a 4 in. x 90-Degree Plain End Schedule 40 Standard Radius Elbow used to change the direction of a conduit run by 90-Degree
Features
Schedule 40 Nonmetallic PVC construction for strength and durability
For indoor or outdoor use
Suitable for aboveground or buried
Plain-end connections are solvent weld
ETL listed Conforms to UL 651 and NEMA TC-3 Conforms to UL 651 and NEMA TC-3
Made in USA
$
28.17
Qty:
Part #:301487
- CANTEX 5133821 is a 4 in. x 90-Degree x 36 in. Radius Plain End Schedule 40 Special Radius Elbow used to change the direction of a conduit run by 90-Degree
Features
Schedule 40 Nonmetallic PVC construction for strength and durability
For indoor or outdoor use
Suitable for aboveground or buried
Plain-end connections are solvent weld
ETL listed Conforms to UL 651 and NEMA TC-3 Conforms to UL 651 and NEMA TC-3
Made in USA
$
87.11
Qty:
Part #:301544
- CANTEX 6441001 is a 1/2 in. Enviro-Flex Straight Liquidtight Connector used to connect Enviro-Flex nonmetallic liquidtight flexible tubing to a box opening or threaded female fitting Features Use with Enviro-Flex Liquid Tight Conduit For use in wet or damp locations Durable non-conductive PVC will not rust or corrode Polypropylene sealing ring UL listed
$
2.45
Qty:
Part #:301770
- CANTEX 5133668 is a 2 in. Conduit Body Type LB which provides pull, splice, and tap access for conductors in a conduit system along with a change in direction Features Type LB Conduit Bodies are used to make a 90-degree turn in a conduit run with one opening on top and one opening exiting from the back opposite the cover Durable non-conductive PVC will not rust or corrode For use with Schedule 40 & 80 conduit Includes lid, gasket, and screws UL listed Made in USA
$
23.33
Qty:
Part #:303374
- CANTEX 5133410 is a 2-Gang Weatherproof Blank Cover designed for use with exposed weatherproof boxes
Features
Includes gasket and screws
For use in wet or damp locations
Durable non-conductive PVC will not rust or corrode
UL listed and UL Marine listed
Made in USA
$
5.50
Qty:
Part #:303756
- CANTEX 5133836 is a 2 in. x 90-Degree x 24 in. Radius Plain End Schedule 40 Special Radius Elbow used to change the direction of a conduit run by 90-Degree
Features
Schedule 40 Nonmetallic PVC construction for strength and durability
For indoor or outdoor use
Suitable for aboveground or buried
Plain-end connections are solvent weld
ETL listed Conforms to UL 651 and NEMA TC-3 Conforms to UL 651 and NEMA TC-3
Made in USA
$
22.99
Qty:
Part #:304347
- CANTEX 5133825 is a 1 in. x 90-Degree Plain End Schedule 40 Standard Radius Elbow used to change the direction of a conduit run by 90-Degree Features Schedule 40 Nonmetallic PVC construction for strength and durability For indoor or outdoor use Suitable for aboveground or buried Plain-end connections are solvent weld ETL listed Conforms to UL 651 and NEMA TC-3 Conforms to UL 651 and NEMA TC-3 Made in USA
$
1.56
Qty:
Part #:305525
- CANTEX 5133743 is a 2 in. Service Entrance Caps which is used as the entry point for overhead power and communication wires into a building
Features
Prevents precipitation from entering the conduit into the building
One 1/2 in. and two 3/4 in. knockouts for wire options
Material is Rigid PVC
UL Listed
Made in USA
$
20.90
Qty:
Part #:305527
- CANTEX 5133735 is a 2 in. Conduit Clamp / Strap which is a U-shaped conduit support used to anchor conduit to interior or exterior surfaces Features Two holes in the feet of the clamp allow mounting the screws or nails Durable non-conductive PVC will not rust or corrode For use with Schedule 40 & 80 conduit UL and CSA listed Made in USA Requires two #10 screws for installation (not included)
$
0.52
Qty:
Part #:510294
- Angled Large Broom, Poly Bristles, 46 7/8" Metal Handle, Yellow/Gray
RCP637500GY
Be the first to write a review
Bristles are cut and shaped for easy sweeping.
Angled bristles are designed for cleaning hard-to-reach places.
Permanent fusion set bristles won't pull out.
$
28.26
Qty:
Part #:713360
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:713363
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:713364
-
Y-Type Cast Iron Strainers
250 lb Screwed 1/2"-3" Class 125 Flanged 2"-6" Class 250 Flanged 2"-6"
Screen chambers won't leak or crush
Both ends of the chambers are precisely machined. This means perfectly round and smooth seating surfaces, as well as a fixed chamber length. Since the screen seats snugly on the machined surface, no particle bigger than the screen opening can escape around the end of the screen.
Screwed retainers easy in, easy out
Straight threads mean it takes less torque to achieve a tight seal with proper gasket compression. Less torque is also required to remove the retainer. For you, that means less danger of "freezing in" than with hard-to-break tapered pipe threads.
Off-center blowdown connections for better dirt removal
Off-center drains on 2-1/2" and 3" strainers allow you to remove liquid and dirt nearly completely when blowing down the strainer. Also, less liquid will spill when the screen retainer is removed.
Many screen choices
Many screen materials, meshes and perforations are available.
Qty:
Part #:713365
Qty:
Displaying: 1 - 24 of 2,061 Matching Items