Baldor
DeWalt
View:
Active Filters :
- Brand: DeWalt Baldor J.H. Williams Random Products
- Size: 1/4in
Qty:
Part #:503696
- 1/4" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:810311
- 12" Long Taper Punches
Designed for aligning the holes in metal pieces through which rivets, bolts, or screws will be inserted
Not intended for driving pins as punch may become stuck in work
Also called line-up aligning or drift punches
Qty:
Part #:501675
- 1/2" Drive SAE 1/4" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:810242
- 5" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:502010
- 3 7/8" Center Punches 1/4"
Pierces or marks work by indentation for starting pilot drills in metal or other materials
Qty:
Part #:500370
- 1/4" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:503684
- 1/4" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:501425
- 1/4" Drive 12-Point SAE 1/4" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:811902
- 1/4" Drive 12-Point SAE 11/32" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Qty:
Part #:810253
- 5 5/8" Cape Chisels
Designed for cutting or grooving keyholes or slots
Qty:
Part #:810256
- 5 3/4" Diamond Point Chisels
Designed for making a V-groove in metal and to clean out inside corner
Qty:
Qty:
Part #:811430
- 1/4" Drive 6-Point SAE 1/4" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
Qty:
Part #:811577
- 3/8" Drive 6-Point SAE 1/4" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
Qty:
Part #:506525
- 5 3/4" Round Nose Chisels
Designed for cutting or grooving keyholes or slots
Qty:
Part #:800794
- 3/8" Drive SAE 1/4" Standard Length Hex Bit Socket
&bull All tools are professional quality, made of high-grade chrome vanadium steel
&bull Sockets feature SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Metal tool box made for years of rugged use
Qty:
Part #:810271
- 5 3/4" Pin Punches
For driving out and removing already loosened pins and keys after initial movement by a solid or starter punch
Qty:
Part #:910-02808-PWR
- Country of Origin TW:
Qty:
Qty:
Part #:910-DCF845P1
- 20V MAX XR® Brushless Cordless 3-Speed 1/4 in. Impact Driver Kit
BRUSHLESS MOTOR delivers 1825 in-lbs of torque and 3400 RPM to drive large diameter screws
COMPLETE TOUGH FASTENING APPLICATIONS on the jobsite with 30% more torque
PRO-LEVEL CONTROL and precision with variable speed trigger and 3-speed setting
Experience Power&trade and drive large diameter screws with the 20V MAX XR® 1/4 in. 3-Speed Impact Driver. Featuring a compact design and 3-speeds, this powerful impact driver delivers 1,825 in-lbs. of max torque and premium user control for a variety of applications. This product is a Chip Ready&trade tool that offers seamless integration into the TOOL CONNECT&trade system (chip sold separately). For user convenience, this kit is packaged with (1) 20V MAX 5Ah Battery, a charger, and a durable storage bag for portability on the jobsite.
$
238.66
Qty:
Displaying: 1 - 22 of 22 Matching Items