Tapping Sleeve
Curb Valves
View:
Active Filters :
- Sub Category: Curb Valves Tapping Sleeve
Part #:204035
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench flats provided for proper installation• ½” – 1” rated for 100 PSIG water pressure• 1 ¼” – 2” rated for 80 PSIG water pressure• Insert stiffeners required on all flexible plastic connections.:
$
154.00
Qty:
Part #:206974
- Straight Ball Valves - Female National Pipe Thread (FNPT) x Female National Pipe Thread (FNPT)
90º ON/OFF TEE OPERATING HEAD FNPT x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
224.87
Qty:
Part #:203863
- Straight Ball Valves - Female National Pipe Thread (FNPT) x Female National Pipe Thread (FNPT)
90º ON/OFF TEE OPERATING HEAD FNPT x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
144.70
Qty:
Part #:204036
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench flats provided for proper installation• ½” – 1” rated for 100 PSIG water pressure• 1 ¼” – 2” rated for 80 PSIG water pressure• Insert stiffeners required on all flexible plastic connections.:
$
237.00
Qty:
Part #:200120
- Straight Ball Valves Compression -33 PEP-7 x -33 PEP-7
90º DEGREE ON/OFF TEE OPERATING HEAD
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
360.45
Qty:
Part #:204037
- Straight Ball Valves - Compression 90º ON/OFF TEE OPERATING HEAD W/LOCK WING -22 CTS x -22 CTS
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
192.22
Qty:
$
941.74
Qty:
Part #:206954
- Straight Ball Valves - Female National Pipe Thread (FNPT) x Female National Pipe Thread (FNPT)
90º ON/OFF TEE OPERATING HEAD FNPT x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
460.52
Qty:
Part #:207154
- Straight Ball Valves - Female National Pipe Thread (FNPT) x Female National Pipe Thread (FNPT)
90º ON/OFF TEE OPERATING HEAD FNPT x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
673.49
Qty:
Part #:206857
- Straight Ball Valves - Compression 90º DEGREE ON/OFF TEE OPERATING HEAD -22 CTS x -22 CTS
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
669.90
Qty:
Part #:206860
- Straight Ball Valves - Compression 90º DEGREE ON/OFF TEE OPERATING HEAD -22 CTS x -22 CTS
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
941.74
Qty:
Part #:204034
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench flats provided for proper installation• ½” – 1” rated for 100 PSIG water pressure• 1 ¼” – 2” rated for 80 PSIG water pressure:
$
233.00
Qty:
Part #:200434
- 622 Tapping Sleeve, Fabricated Steel, Neck Seal - For tapping size-on-size or reducing branch connections on new or existing pipe
Description Tapping sleeve.Application For 4" pipe and larger reducing and size-on-size flanged outlets. Available with ¾"-6"threaded outlets.Key Features
&bullEasy to install&bullHas range to reduce inventory
&bullMeets AWWA C223 Standards&bullEpoxy Finish meets AWWA C213 Standards
&bullVirtually 360º support of the pipe
&bullRoll-resistant gasket will not bind
&bullGasket seal increases with line pressure
&bullNo special tools required to install the sleeve
&bullFlanged outlets are recessed to accept tapping valves
&bullFlexi-Coat® Fusion-Bonded Epoxy Finish is standard for superior corrosion resistance
&bull¾" test outlet to allow hydrostatic pressure test before tapping the pipe (not available in standard 4" x 4")
$
728.56
Qty:
Part #:204941
- 622 Tapping Sleeve, Fabricated Steel, Neck Seal - For tapping size-on-size or reducing branch connections on new or existing pipe
Description Tapping sleeve.Application For 4" pipe and larger reducing and size-on-size flanged outlets. Available with ¾"-6"threaded outlets.Key Features
&bullEasy to install&bullHas range to reduce inventory
&bullMeets AWWA C223 Standards&bullEpoxy Finish meets AWWA C213 Standards
&bullVirtually 360º support of the pipe
&bullRoll-resistant gasket will not bind
&bullGasket seal increases with line pressure
&bullNo special tools required to install the sleeve
&bullFlanged outlets are recessed to accept tapping valves
&bullFlexi-Coat® Fusion-Bonded Epoxy Finish is standard for superior corrosion resistance
&bull¾" test outlet to allow hydrostatic pressure test before tapping the pipe (not available in standard 4" x 4")
$
796.07
Qty:
Part #:202496
- 622 Tapping Sleeve, Fabricated Steel, Neck Seal - For tapping size-on-size or reducing branch connections on new or existing pipe
Description Tapping sleeve.Application For 4" pipe and larger reducing and size-on-size flanged outlets. Available with ¾"-6"threaded outlets.Key Features
&bullEasy to install&bullHas range to reduce inventory
&bullMeets AWWA C223 Standards&bullEpoxy Finish meets AWWA C213 Standards
&bullVirtually 360º support of the pipe
&bullRoll-resistant gasket will not bind
&bullGasket seal increases with line pressure
&bullNo special tools required to install the sleeve
&bullFlanged outlets are recessed to accept tapping valves
&bullFlexi-Coat® Fusion-Bonded Epoxy Finish is standard for superior corrosion resistance
&bull¾" test outlet to allow hydrostatic pressure test before tapping the pipe (not available in standard 4" x 4")
$
998.61
Qty:
Part #:204942
- 622 Tapping Sleeve, Fabricated Steel, Neck Seal - For tapping size-on-size or reducing branch connections on new or existing pipe
Description Tapping sleeve.Application For 4" pipe and larger reducing and size-on-size flanged outlets. Available with ¾"-6"threaded outlets.Key Features
&bullEasy to install&bullHas range to reduce inventory
&bullMeets AWWA C223 Standards&bullEpoxy Finish meets AWWA C213 Standards
&bullVirtually 360º support of the pipe
&bullRoll-resistant gasket will not bind
&bullGasket seal increases with line pressure
&bullNo special tools required to install the sleeve
&bullFlanged outlets are recessed to accept tapping valves
&bullFlexi-Coat® Fusion-Bonded Epoxy Finish is standard for superior corrosion resistance
&bull¾" test outlet to allow hydrostatic pressure test before tapping the pipe (not available in standard 4" x 4")
$
1,068.95
Qty:
Part #:204950
- 622 Tapping Sleeve, Fabricated Steel, Neck Seal - For tapping size-on-size or reducing branch connections on new or existing pipe
Description Tapping sleeve.Application For 4" pipe and larger reducing and size-on-size flanged outlets. Available with ¾"-6"threaded outlets.Key Features
&bullEasy to install&bullHas range to reduce inventory
&bullMeets AWWA C223 Standards&bullEpoxy Finish meets AWWA C213 Standards
&bullVirtually 360º support of the pipe
&bullRoll-resistant gasket will not bind
&bullGasket seal increases with line pressure
&bullNo special tools required to install the sleeve
&bullFlanged outlets are recessed to accept tapping valves
&bullFlexi-Coat® Fusion-Bonded Epoxy Finish is standard for superior corrosion resistance
&bull¾" test outlet to allow hydrostatic pressure test before tapping the pipe (not available in standard 4" x 4")
$
866.38
Qty:
Part #:204952
- 622 Tapping Sleeve, Fabricated Steel, Neck Seal - For tapping size-on-size or reducing branch connections on new or existing pipe
Description Tapping sleeve.Application For 4" pipe and larger reducing and size-on-size flanged outlets. Available with ¾"-6"threaded outlets.Key Features
&bullEasy to install&bullHas range to reduce inventory
&bullMeets AWWA C223 Standards&bullEpoxy Finish meets AWWA C213 Standards
&bullVirtually 360º support of the pipe
&bullRoll-resistant gasket will not bind
&bullGasket seal increases with line pressure
&bullNo special tools required to install the sleeve
&bullFlanged outlets are recessed to accept tapping valves
&bullFlexi-Coat® Fusion-Bonded Epoxy Finish is standard for superior corrosion resistance
&bull¾" test outlet to allow hydrostatic pressure test before tapping the pipe (not available in standard 4" x 4")
$
1,518.98
Qty:
Part #:205235
-
663 Tapping Sleeve, Stainless Steel, Finger Lug Style, Full Gasket - For tapping size-on-size or reducing branch connections on new or existing pipe
Description All stainless steel tapping sleeve with 360º gasket seal.Application For tapping size-on-size or reducing branch connections on new or existing pipe.Key Features&bull Easy to install&bull Range helps reduce inventory&bull Meets applicable AWWA C223 Standards&bull Molded-in ring in the gasket to ensure effective sealing&bull Nylon washers provided to improve bolt torque capability&bull Heavy gauge, all-Stainless Steel body for rugged performance&bull Fully chemically passivated for maximum corrosion protection&bull ¾" test outlet to allow hydrostatic pressure test before tapping the pipe&bull 360º seal provides maximum support and reinforcement around the pipe in case of pipe break&bull Body drawn out to accept the outlet neck adding to the overall strength of the area under the most stress
$
1,933.11
Qty:
Part #:204033
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench flats provided for proper installation• ½” – 1” rated for 100 PSIG water pressure• 1 ¼” – 2” rated for 80 PSIG water pressure:
$
142.00
Qty:
$
786.56
Qty:
$
573.31
Qty:
Part #:130-5139-116
- Straight Ball Valves - Flare x Female National PipeThread (FNPT) Flare x FNPT
90º ON/OFF TEE OPERATING HEAD WITH LOCKWING
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
177.14
Qty:
$
801.37
Qty:
Displaying: 1 - 24 of 27 Matching Items