1-1/2in
Electrical Equipment
View:
Active Filters :
- Main Category: Electrical Equipment
- Size: 1-1/2in 1-gang
$
45.04
Qty:
Part #:303954
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$
14.50
Qty:
Part #:303997
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$
8.32
Qty:
Part #:304966
- Extremely durable for hard-use institutional applications. Spring-loaded covers close automatically when plugs are removed. Die-cast copper-free aluminum construction. Stainless steel springs. Screws and spring covers are chrome-plated brass. Baked-on lacquer finish. Heavy rubber gaskets provide positive seal. All covers below are for 4 screw mounting only. Comply with 2005 NEC Section 406.8(A) and 406.8(B)(2).
$
12.35
Qty:
Part #:307976
- Appleton liquidtight STF Series connectors with threaded hubs are female ST Series connectors. They are designed to be used when making connection from liquidtight flexible metal conduit to threaded rigid conduit and IMC. The compact design results in a connector that offers a small turning radius.
$
35.50
Qty:
Part #:303701
- One Gang Heavy Cast Aluminum Cover Duplex Receptacle Horizontal, Gray
Extremely durable for hard-use institutional applications.
Spring-loaded covers close automatically when plugs are removed.
Die-cast copper-free aluminum construction.
Stainless steel springs.
Screws and spring covers are chrome-plated brass.
Baked-on lacquer finish.
Heavy rubber gaskets provide positive seal.
All covers below are for 4 screw mounting only.
Comply with 2005 NEC Section 406.8(A) and 406.8(B)(2).
CSA File Number 16807
Qty:
Part #:303205
- WP BOX 1G 3 HOLE 1/2 WPB23
Wide range of sizes, depths, and gangs.
Baked-on electrostatic, polyester, powder paint for superior scratch and corrosion resistance.
2 closure plugs and mounting lugs furnished with all boxes.
UL Listed for wet and/or damp locations with appropriate cover.
Designed for both interior and exterior applications.
Will accept standard 4 screw mounting covers and single gang weatherproof covers.
Simply strike desired knockout studs with a sharp hammer blow for clean mounting holes.
Heavy die-cast aluminum.
For covering patents, see www.legrand.us/patents.
CSA File Number 17695
Qty:
Part #:300841
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$
2.70
Qty:
Part #:302661
- Appleton and O-Z/Gedney offer ETP 5000S Series steel EMT set screw couplings. They are used to ground and secure EMT raceway sections together.
$
4.64
Qty:
Part #:302665
- Appleton and O-Z/Gedney Hang-On hangers are designed secure rigid metal conduit IMC or EMT to threaded rod supports or directly to mounting surfaces.
$
2.24
Qty:
Part #:306983
- Appleton and O-Z/Gedney conduit bushings are used with a locknut to terminate rigid metal conduit or IMC conduit to a box or enclosure. They provide a smooth pulling surface for wires.
$
1.72
Qty:
Part #:307353
- Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
$
2.05
Qty:
Part #:307367
- Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
$
1.06
Qty:
Part #:308183
- O-Z/Gedney offers clamps and straps. They are used to secure oval/round cables or support runs of rigid metal conduit IMC and EMT.
$
0.91
Qty:
Part #:308317
- Appleton Form 35 Malleable Iron Conduit Outlet Bodies Covers and Gaskets are used to connect and change direction of conduit runs. In addition to making bends in a conduit system they allow connections for branch runs. These conduit bodies serve as pulling fittings and permit access to conductors for splicing and maintenance.
$
61.36
Qty:
$
8.60
Qty:
$
4.14
Qty:
$
2.95
Qty:
Part #:307182
- Toggle Switch Openings, One Gang, 302/304 Stainless Steel
Type 302/304 Stainless Steel, non-magnetic .032''' nominal thickness.
Brushed finish.
This alloy contains 18% chromium and 8% nickel for superior resistance to corrosion.
Recommended for use in food processing plants, dairies, chemical plants, and other industrial, institutional, and commercial applications where corrosive atmospheres exist.
Standard, Jumbo, and Tandem plates available, as well as special Panel plates up to 5-gangs high and 10-gangs wide.
Packaged in protective film, with finish-matching screws.
Variety of special plated finishes.
Paintable to match plastic plates.
Can be silk-screened or engraved, and custom punched with over 300 opening styles.
Qty:
Part #:307185
- Duplex Receptacle Openings, One Gang, 302/304 Stainless Steel
Type 302/304 Stainless Steel, non-magnetic .032''' nominal thickness.
Brushed finish.
This alloy contains 18% chromium and 8% nickel for superior resistance to corrosion.
Recommended for use in food processing plants, dairies, chemical plants, and other industrial, institutional, and commercial applications where corrosive atmospheres exist.
Standard, Jumbo, and Tandem plates available, as well as special Panel plates up to 5-gangs high and 10-gangs wide.
Packaged in protective film, with finish-matching screws.
Variety of special plated finishes.
Paintable to match plastic plates.
Can be silk-screened or engraved, and custom punched with over 300 opening styles.
Qty:
Part #:307154
- Blank Plates, Box Mounted, One Gang, Ivory
Molded of rugged, practically indestructible self-extinguishing nylon. ('TP' series only.)
Available in 'TP' series, extra 3/16 inch width and height than Standard size plates and 'TPJ' series, extra 3/16 inch width and height than Junior-Jumbo size plates.
Available in Ivory, White, Brown, Gray, Black, Blue, Orange, Red, and Light Almond.
Preferred for hospital, industrial, institutional, and other high-abuse applications.
Nominal thickness, .070 inch.
cULus ListingNumber 143222
Qty:
Part #:300310
- Single Gang Cast While-In-Use Cover, Gray
Compliant with National Electric Code (NEC) Section 406.8(B)(1) for wet locations.
UL listed for ''Extra-Duty'' applications.
Heavy cast aluminum construction.
Corner hinge allows for vertical or horizontal mounting.
Device inserts allow for multiple device types.
Install without removing electrical device thanks to keyed mounting holes.
Cord flap gaskets inhibit water splash and insects, all gaskets are factory installed.
Accepts padlocks.
Qty:
Part #:303196
- One Gang Blank Cover, Brushed Aluminum
Designed for both interior and exterior applications.
Universal aluminum mounting plates.
Gray, bronze and white models have baked-on electrostatic, polyester, powder paint for superior scratch and corrosion resistance.
CSA File Number 17695
Qty:
Displaying: 1 - 24 of 93 Matching Items