1-gang
Electrical Equipment
View:
Active Filters :
- Main Category: Electrical Equipment
- Size: 1-gang 1in x 3/4in 3in 500MCM
$
9.33
Qty:
Part #:303321
- Appleton and O-Z/Gedney offer ETP 5000S Series steel EMT set screw couplings. They are used to ground and secure EMT raceway sections together.
$
15.79
Qty:
Part #:304002
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$
15.97
Qty:
Part #:304966
- Extremely durable for hard-use institutional applications. Spring-loaded covers close automatically when plugs are removed. Die-cast copper-free aluminum construction. Stainless steel springs. Screws and spring covers are chrome-plated brass. Baked-on lacquer finish. Heavy rubber gaskets provide positive seal. All covers below are for 4 screw mounting only. Comply with 2005 NEC Section 406.8(A) and 406.8(B)(2).
$
12.35
Qty:
Part #:307082
- Appleton RB Series reducers are explosionproof and dust-ignitionproof. They are designed to reduce conduit entries to a smaller size and are used in threaded rigid and IMC conduit systems.
$
3.13
Qty:
Part #:307245
- Appleton™ Type RW steel reducing washers are used to reduce the size of a knockout or slip hole in a sheet metal enclosure to a smaller trade size..
$
0.76
Qty:
Part #:303701
- One Gang Heavy Cast Aluminum Cover Duplex Receptacle Horizontal, Gray
Extremely durable for hard-use institutional applications.
Spring-loaded covers close automatically when plugs are removed.
Die-cast copper-free aluminum construction.
Stainless steel springs.
Screws and spring covers are chrome-plated brass.
Baked-on lacquer finish.
Heavy rubber gaskets provide positive seal.
All covers below are for 4 screw mounting only.
Comply with 2005 NEC Section 406.8(A) and 406.8(B)(2).
CSA File Number 16807
Qty:
Part #:303205
- WP BOX 1G 3 HOLE 1/2 WPB23
Wide range of sizes, depths, and gangs.
Baked-on electrostatic, polyester, powder paint for superior scratch and corrosion resistance.
2 closure plugs and mounting lugs furnished with all boxes.
UL Listed for wet and/or damp locations with appropriate cover.
Designed for both interior and exterior applications.
Will accept standard 4 screw mounting covers and single gang weatherproof covers.
Simply strike desired knockout studs with a sharp hammer blow for clean mounting holes.
Heavy die-cast aluminum.
For covering patents, see www.legrand.us/patents.
CSA File Number 17695
Qty:
Part #:300863
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports
$
6.01
Qty:
Part #:301354
- CANTEX 6141630 is a 3 in. Schedule 40 Standard Center Stop Coupling used to join lengths of conduit pipe together with two solvent weld socket ends
Features
For use with Schedule 40 and Schedule 80 conduit. May also be used in EB & DB Duct applications.
Center stop to help determine proper depth of connection
For use aboveground and underground and non-conductive and sunlight resistant
Meets NEMA TC-3 Standards
UL and CSA listed
Made in USA
$
1.43
Qty:
Part #:307182
- Toggle Switch Openings, One Gang, 302/304 Stainless Steel
Type 302/304 Stainless Steel, non-magnetic .032''' nominal thickness.
Brushed finish.
This alloy contains 18% chromium and 8% nickel for superior resistance to corrosion.
Recommended for use in food processing plants, dairies, chemical plants, and other industrial, institutional, and commercial applications where corrosive atmospheres exist.
Standard, Jumbo, and Tandem plates available, as well as special Panel plates up to 5-gangs high and 10-gangs wide.
Packaged in protective film, with finish-matching screws.
Variety of special plated finishes.
Paintable to match plastic plates.
Can be silk-screened or engraved, and custom punched with over 300 opening styles.
Qty:
Part #:307185
- Duplex Receptacle Openings, One Gang, 302/304 Stainless Steel
Type 302/304 Stainless Steel, non-magnetic .032''' nominal thickness.
Brushed finish.
This alloy contains 18% chromium and 8% nickel for superior resistance to corrosion.
Recommended for use in food processing plants, dairies, chemical plants, and other industrial, institutional, and commercial applications where corrosive atmospheres exist.
Standard, Jumbo, and Tandem plates available, as well as special Panel plates up to 5-gangs high and 10-gangs wide.
Packaged in protective film, with finish-matching screws.
Variety of special plated finishes.
Paintable to match plastic plates.
Can be silk-screened or engraved, and custom punched with over 300 opening styles.
Qty:
Part #:307154
- Blank Plates, Box Mounted, One Gang, Ivory
Molded of rugged, practically indestructible self-extinguishing nylon. ('TP' series only.)
Available in 'TP' series, extra 3/16 inch width and height than Standard size plates and 'TPJ' series, extra 3/16 inch width and height than Junior-Jumbo size plates.
Available in Ivory, White, Brown, Gray, Black, Blue, Orange, Red, and Light Almond.
Preferred for hospital, industrial, institutional, and other high-abuse applications.
Nominal thickness, .070 inch.
cULus ListingNumber 143222
Qty:
Part #:300310
- Single Gang Cast While-In-Use Cover, Gray
Compliant with National Electric Code (NEC) Section 406.8(B)(1) for wet locations.
UL listed for ''Extra-Duty'' applications.
Heavy cast aluminum construction.
Corner hinge allows for vertical or horizontal mounting.
Device inserts allow for multiple device types.
Install without removing electrical device thanks to keyed mounting holes.
Cord flap gaskets inhibit water splash and insects, all gaskets are factory installed.
Accepts padlocks.
Qty:
Part #:303196
- One Gang Blank Cover, Brushed Aluminum
Designed for both interior and exterior applications.
Universal aluminum mounting plates.
Gray, bronze and white models have baked-on electrostatic, polyester, powder paint for superior scratch and corrosion resistance.
CSA File Number 17695
Qty:
Part #:307371
- Weatherproof Single Gang Box, Gray
Wide range of sizes, depths, and gangs.
Baked-on electrostatic, polyester, powder paint for superior scratch and corrosion resistance.
2 closure plugs and mounting lugs furnished with all boxes.
UL Listed for wet and/or damp locations with appropriate cover.
Designed for both interior and exterior applications.
Will accept standard 4 screw mounting covers and single gang weatherproof covers.
Simply strike desired knockout studs with a sharp hammer blow for clean mounting holes.
Heavy die-cast aluminum.
For covering patents, see www.legrand.us/patents.
CSA File Number 17695
Qty:
Part #:300070
- Appleton HUB-B threaded conduit hubs with bonding screw are general purpose fittings designed for RMC and IMC. They provide threaded terminations in sheet metal enclosures and are suitable for service entrances.
$
96.78
Qty:
Part #:300341
- Power Outlet Receptacle Openings, One Gang, 302/304 Stainless Steel
Type 302/304 Stainless Steel, non-magnetic .032''' nominal thickness.
Brushed finish.
This alloy contains 18% chromium and 8% nickel for superior resistance to corrosion.
Recommended for use in food processing plants, dairies, chemical plants, and other industrial, institutional, and commercial applications where corrosive atmospheres exist.
Standard, Jumbo, and Tandem plates available, as well as special Panel plates up to 5-gangs high and 10-gangs wide.
Packaged in protective film, with finish-matching screws.
Variety of special plated finishes.
Paintable to match plastic plates.
Can be silk-screened or engraved, and custom punched with over 300 opening styles.
Qty:
$
29.97
Qty:
Part #:301413
- CANTEX 5133829 is a 2-1/2 in. x 90-Degree Plain End Schedule 40 Standard Radius Elbow used to change the direction of a conduit run by 90-Degree
Features
Schedule 40 Nonmetallic PVC construction for strength and durability
For indoor or outdoor use
Suitable for aboveground or buried
Plain-end connections are solvent weld
ETL listed Conforms to UL 651 and NEMA TC-3 Conforms to UL 651 and NEMA TC-3
Made in USA
$
12.63
Qty:
Displaying: 1 - 24 of 61 Matching Items