Appleton
Electrical Equipment
View:
Active Filters :
- Main Category: Electrical Equipment
- Brand: Appleton
- Electrical Boxes, Conduit, Strut, and Raceway: Electrical Fittings
- Alt. Size: 1" x 1/2" 2-1/2" x 2" 2-1/2"
Part #:307246
- Appleton™ Type RW steel reducing washers are used to reduce the size of a knockout or slip hole in a sheet metal enclosure to a smaller trade size..
$
0.76
Qty:
Part #:307081
- Appleton RB Series reducers are explosionproof and dust-ignitionproof. They are designed to reduce conduit entries to a smaller size and are used in threaded rigid and IMC conduit systems.
$
3.16
Qty:
Part #:302502
- Appleton and O-Z/Gedney offer ETP 4000S Series steel EMT set screw connectors. They are used to ground and secure EMT raceways to boxes and enclosures. The 4000S Series have a male NPS threaded hub and are available with or without an insulated throat.
$
16.91
Qty:
Part #:303001
- Appleton and O-Z/Gedney offer ETP 5000S Series steel EMT set screw couplings. They are used to ground and secure EMT raceway sections together.
$
13.87
Qty:
Part #:304001
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$
13.89
Qty:
Part #:306954
- Appleton and O-Z/Gedney rigid conduit and IMC locknuts are used to secure and ground conduits and fittings to enclosures and prevents loosening due to vibration or motion. They are available in plain gasketed and bonding styles.
$
9.13
Qty:
Part #:306985
- Appleton and O-Z/Gedney conduit bushings are used with a locknut to terminate rigid metal conduit or IMC conduit to a box or enclosure. They provide a smooth pulling surface for wires.
$
6.93
Qty:
Part #:307072
- Appleton and O-Z/Gedney threaded enlargers are used to adapt an outlet hole to the next larger size of conduit. The offset nipples provide box to box connection of knockouts and allows misaligned knockout connection by rolling the offset nipple until aligned with each knockout. Bushed nipples are used through knockouts to connect box to conduit coupling. They can be used with a locknut to connect two boxes side by side or back to back or to connect fixture housings and continuous runs.
$
21.96
Qty:
Part #:307100
- Appleton RB Series reducers are explosionproof and dust-ignitionproof. They are designed to reduce conduit entries to a smaller size and are used in threaded rigid and IMC conduit systems
$
22.60
Qty:
Part #:307125
- O-Z/Gedney threaded three piece couplings join two lengths of conduit when neither can be turned. Elbows provide a 90 change of direction in a conduit run. Gasket elbows also provide a compact wire pulling point.
$
144.81
Qty:
Part #:307275
- Appleton and O-Z/Gedney Hang-On hangers are designed secure rigid metal conduit IMC or EMT to threaded rod supports or directly to mounting surfaces.
$
3.43
Qty:
Part #:307355
- Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
$
7.80
Qty:
Part #:307980
- Appleton liquidtight STF Series connectors with threaded hubs are female ST Series connectors. They are designed to be used when making connection from liquidtight flexible metal conduit to threaded rigid conduit and IMC. The compact design results in a connector that offers a small turning radius.
$
307.27
Qty:
Part #:310652
- Appleton and O-Z/Gedney offer NEER ECO aluminum entrance caps. They are a clamp type aluminum entrance cap for threaded or unthreaded rigid conduit IMC or EMT service masts.
$
86.48
Qty:
$
2,214.71
Qty:
Displaying: 1 - 15 of 15 Matching Items