Electrical Fittings
Electrical Equipment
View:
Active Filters :
- Main Category: Electrical Equipment
- Electrical Boxes, Conduit, Strut, and Raceway: Electrical Fittings
- Alt. Size: 1-1/2" x 1/2" 1/2" 3-1/2" 3/4" x 1/2"
$
2.46
Qty:
Part #:301327
- Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
$
0.86
Qty:
$
10.45
Qty:
Part #:302425
- Appleton HUB-B threaded conduit hubs with bonding screw are general purpose fittings designed for RMC and IMC. They provide threaded terminations in sheet metal enclosures and are suitable for service entrances.
$
11.72
Qty:
Part #:303757
- Appleton and O-Z/Gedney offer NEER zinc cable and conduit connectors for terminating flexible metal conduit in a dry location box or enclosure or joining lengths of flexible metal conduit. Type SC straight squeeze connectors Type AC 90 two screw clamp connectors and Type DC-5500 duplex single screw clamp connectors are used to make a termination of flexible metal conduit. Type FC set screw connectors are used to terminate 1/2 regular wall steel or aluminum flexible conduit. Type GC screw-in connectors are for use with flexible metal conduit. Type GX screw-in connectors are used to join lengths of flexible metal conduit.
$
1.35
Qty:
Part #:303915
- Appleton and O-Z/Gedney K-clamps are designed to secure rigid metal conduit IMC or EMT. They can be used across parallel or perpendicular to beam channel and angle supports.
$
6.97
Qty:
Part #:305112
- Appleton and O-Z/Gedney offer NEER zinc set screw offset nipples. The TN-50 is a set screw type offset connector with locknut. It is used to make a slight adjustment in terminating the end of a run of EMT to an enclosure or box.
$
8.96
Qty:
Part #:307064
- Appleton and O-Z/Gedney threaded enlargers are used to adapt an outlet hole to the next larger size of conduit. The offset nipples provide box to box connection of knockouts and allows misaligned knockout connection by rolling the offset nipple until aligned with each knockout. Bushed nipples are used through knockouts to connect box to conduit coupling. They can be used with a locknut to connect two boxes side by side or back to back or to connect fixture housings and continuous runs.
$
1.11
Qty:
Part #:307117
- O-Z/Gedney threaded three piece couplings join two lengths of conduit when neither can be turned. Elbows provide a 90 change of direction in a conduit run. Gasket elbows also provide a compact wire pulling point.
$
6.33
Qty:
Part #:307226
- O-Z/Gedney threaded three piece couplings join two lengths of conduit when neither can be turned. Elbows provide a 90 change of direction in a conduit run. Gasket elbows also provide a compact wire pulling point.
$
10.96
Qty:
Part #:307244
- Appleton™ Type RW steel reducing washers are used to reduce the size of a knockout or slip hole in a sheet metal enclosure to a smaller trade size..
$
0.44
Qty:
Part #:307320
- Appleton offers beam clamps straps clamps and clamp backs for rigid metal conduit or imc. Beam clamps provide support for conduit hanging systems. Two-hole straps are used to support rigid metal conduit and IMC. Clamp backs provide spacing from mounting surfaces when they are used with pipe clamps.
$
1.00
Qty:
Part #:309495
- O-Z/Gedney UNY and UNF explosionproof and dust-ignitionproof unions are used for joining conduit and connecting conduit to enclosures. They facilitate modifications and permit the removal of enclosures without turning or removing conduit.
$
40.88
Qty:
Part #:309685
- Appleton and O-Z/Gedney offer NEER zinc gland compression connectors and couplings. TC-600 couplings are used to join lengths of steel EMT for concretetight dry or damp location applications. TC-600 connectors are used to secure and terminate steel EMT to knockouts in concretetight box dry or damp location applications.
$
0.92
Qty:
Part #:300085
- Appleton and O-Z/Gedney threaded enlargers are used to adapt an outlet hole to the next larger size of conduit. The offset nipples provide box to box connection of knockouts and allows misaligned knockout connection by rolling the offset nipple until aligned with each knockout. Bushed nipples are used through knockouts to connect box to conduit coupling. They can be used with a locknut to connect two boxes side by side or back to back or to connect fixture housings and continuous runs.
$
3.53
Qty:
Part #:300290
- Appleton liquidtight ST Series plain throat and STB Series insulated throat connectors provide a dependable connection for liquidtight flexible metal conduit. Available in straight 45 and 90 styles and trade sizes from 3/8 through 4 . The compact design results in a connector that offers a small turning radius. They seal out oil water dust dirt and fumes.
$
13.30
Qty:
Displaying: 25 - 48 of 72 Matching Items