Fasteners and Hardware | 5/32in | 8mm-1.25 | 9/16in-12

E-Z Lok 5mm-0.8 x 8mm-1.25 450-5 Threaded Insert for Metal - Standard Wall - Carbon Steel

Part #:810111

E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - M5-0.8 x M8-1.25 STRONG THREADS MADE EASY All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools. E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool. E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes. The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours). Features Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary) Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps Self-Locking pre-applied adhesive activates upon installation Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi. Applications Soft metals aluminum, cast iron, magnesium, etc. Installation Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3. Simply drill the appropriately sized hole with a standard drill Tap the hole with a standard tap Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool. E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.

$2.60 MSRP $ 1.61

Qty:

add to cart Add to Cart Quantity:

E-Z Lok 8mm-1.25 x 1/2in-13 653-8 Threaded Insert for Metal - Standard Wall - Stainless Steel

Part #:810112

E-Z LOK&trade Threaded Insert for Metal - Standard Wall - 303 Stainless - M8-1.25 x 1/2-13 STRONG THREADS MADE EASY All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools. E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool. E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes. The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours). Features Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary) Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps Self-Locking pre-applied adhesive activates upon installation Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi. Applications Soft metals aluminum, cast iron, magnesium, etc. Installation Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3. Simply drill the appropriately sized hole with a standard drill Tap the hole with a standard tap Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool. E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.

$5.45 MSRP $ 3.36

Qty:

add to cart Add to Cart Quantity:

E-Z Lok 10mm-1.5 x 9/16in-12 650-10 Threaded Insert for Metal - Standard Wall - Carbon Steel

Part #:810113

E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - M10-1.5 x 9/16-12 STRONG THREADS MADE EASY All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools. E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool. E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes. The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours). Features Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary) Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps Self-Locking pre-applied adhesive activates upon installation Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi. Applications Soft metals aluminum, cast iron, magnesium, etc. Installation Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3. Simply drill the appropriately sized hole with a standard drill Tap the hole with a standard tap Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool. E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.

$2.38 MSRP $ 1.47

Qty:

add to cart Add to Cart Quantity:

E-Z Lok 4mm-0.7 x 8mm-1.25 450-4 Threaded Insert for Metal - Standard Wall - Carbon Steel

Part #:810120

E-Z LOK&trade Threaded Insert for Metal - Standard Wall - Carbon Steel - M4-0.7 x M8-1.25 STRONG THREADS MADE EASY All solid construction E-Z LOK threaded inserts install with standard tools. No special drills...no special taps...no special installation tools. E-Z LOK external threads are standard size and pitch to permit the use of standard drills and taps. E-Z LOKs can be installed with a screwdriver, bolt/jam nut (except IC series), or optional power drive tool. E-Z LOKs will not back out or vibrate loose. Immediately upon installation, microencapsulated adhesive begins to set and the newly installed inserts are fastener-ready in 3-5 minutes. The adhesive seals against liquids and gases to 6,000 psi when fully cured (72 hours). Features Easy to install solid threaded inserts install with standard tools, simply drill, tap and thread like any ordinary fastener (no special taps or installation tools are necessary) Strength carbon steel solid threaded inserts are screw machined out of solid steel for a stronger overall product Standard OD Threads solid threaded inserts for metal permit the use of standard drills and taps Self-Locking pre-applied adhesive activates upon installation Vibration Resistant adhesive secures the carbon steel solid threaded insert into place so it won&rsquot back out Seals against Liquids/Gases solid threaded inserts are pressurized up to 6,000 psi. Applications Soft metals aluminum, cast iron, magnesium, etc. Installation Unlike E-Z Coil&trade inserts, which require a special tap and installation tool, E-Z LOK&trade (Solid Wall) threaded inserts for metal are installed using standard tools, and installation is as easy as 1-2-3. Simply drill the appropriately sized hole with a standard drill Tap the hole with a standard tap Turn in the E-Z LOK&trade (Solid Wall) insert like an ordinary fastener with a screwdriver, bolt and jam nut, or an E-Z LOK&trade drive tool. E-Z LOK&trade (Solid Wall) threaded inserts are self-locking and open immediately upon installation. The pre-applied LOCTITE&trade on the external threads sets immediately allowing for the newly installed insert to be fastener ready.E-Z LOK solid wall threaded inserts are typically installed with the slots up. The slots accommodate a screwdriver or E-Z LOK drive tool. When using a bolt and jam nuts for installation, the slotted end of the insert can be either up or down.Important Note Hole size requirements may vary depending on a number of factors, including material and tools. We recommend you test your particular application before ordering. Contact us for free samples.

$2.30 MSRP $ 1.42

Qty:

add to cart Add to Cart Quantity: