1-1/2in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Size: 1-1/2in 1in 13/16in 17MM
Qty:
Qty:
Part #:503694
- 1" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:808226
- RATCHET & HANDLE ONLY&bull Ratchet knob indicates forward and reverse.&bull Die heads snap in from both sides and lock in place.
Qty:
Qty:
Part #:500514
- 1-1/2" Conduit Size Slug-Buster® Manual Knockout Set
Unique punch profile splits slugs allowing for easy slug removal
Knurled edge for better grip
Laser markings for quick part identification
Alignment markings for improved accuracy
Punch and die Made in USA
Replaces 7211BB-1-1/2
Qty:
closeout
$28.99 MSRP
$
26.06
Part #:500221
- CLOSEOUTS Only 21 Left!
- Crescent Lufkin 25 ft. Tape Measures, 1" Blade (Discontinued being replaced by PHV1425N)
Qty:
Part #:509210
- Country of Origin US:
Qty:
Qty:
Qty:
Qty:
Qty:
Qty:
closeout
$98.80 MSRP
$
61.35
Part #:503074
- CLOSEOUTS Only 3 Left!
- Heavy Service C-Clamp Capacity 1-7/8" &bull Especially designed for heavy duty service, frames are drop-forged and heat-treated for maximum strength and reduced springing &bull Screws are made of special grade steel and are heat-treated for added strength not found in typical case-hardened screws &bull To tighten, the square headed screw must be turned with a wrench &bull Ideal for the most demanding applications such as construction and heavy industry &bull Square head screw allows tightening with wrench for extra heavy duty clamping requirements &bull Greater anvil surface for gripping larger work pieces and for greater stability
Qty:
Part #:500382
- 1" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:500391
- 1-1/2" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:503736
- 1-1/2" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Qty:
Qty:
Qty:
closeout
$46.00 MSRP
$
39.95
Part #:511853
- CLOSEOUTS Only 7 Left!
-
1" Wire Rope Clip, Forged Carbon Steel, Galvanized(Discontinued being replaced by 490-M254)
Base is Drop-Forged Carbon Steel
Hot Galvanized to ASTM A-153 to Resist Rust and Corrosion
U-Bolts Are colored Blue for Identification Purposes and Use Heavy Duty Hex Nuts (UNC-2A)
Designed to Meet Federal Specifications, FF-C-450, Type 1, Class 1
Designed to Meet or Exceed All Requirements of ASME B30.26 Including Identification, Ductility, Design Factor and Temperature
Permanently Marked with Size and Manufacturer
Sizes 1/4" and Above Marked with USA and Date Code
Sizes 1/8" Through 1-1/4" Are Supplied Bagged and Unassembled
Note See Application and Warning Information
Qty:
Part #:808091
- Manual Threader Pipe & Bolt Dies
Qty:
Part #:808217
- RATCHET & HANDLE ONLY&bull Ratchet knob indicates forward and reverse.&bull Die heads snap in from both sides and lock in place.
Qty:
Displaying: 25 - 48 of 132 Matching Items