1-1/8in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Size: 1-1/8in 2in 10mm-24mm 23MM
Part #:501426
- 1" Drive 12-Point SAE 2" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
closeout
$134.00 MSRP
$
83.21
Part #:807915
- CLOSEOUTS Only 2 Left!
- Heavy Service C-Clamp Capacity 2-11/32" &bull Especially designed for heavy duty service, frames are drop-forged and heat-treated for maximum strength and reduced springing &bull Screws are made of special grade steel and are heat-treated for added strength not found in typical case-hardened screws &bull To tighten, the square headed screw must be turned with a wrench &bull Ideal for the most demanding applications such as construction and heavy industry &bull Square head screw allows tightening with wrench for extra heavy duty clamping requirements &bull Greater anvil surface for gripping larger work pieces and for greater stability
Qty:
Qty:
Qty:
Qty:
closeout
$51.35 MSRP
$
48.25
Part #:511854
- CLOSEOUTS Only 10 Left!
-
1-1/8" Wire Rope Clip, Forged Carbon Steel, Galvanized(Discontinued being replaced by 490-M255)
Base is Drop-Forged Carbon Steel
Hot Galvanized to ASTM A-153 to Resist Rust and Corrosion
U-Bolts Are colored Blue for Identification Purposes and Use Heavy Duty Hex Nuts (UNC-2A)
Designed to Meet Federal Specifications, FF-C-450, Type 1, Class 1
Designed to Meet or Exceed All Requirements of ASME B30.26 Including Identification, Ductility, Design Factor and Temperature
Permanently Marked with Size and Manufacturer
Sizes 1/4" and Above Marked with USA and Date Code
Sizes 1/8" Through 1-1/4" Are Supplied Bagged and Unassembled
Note See Application and Warning Information
Qty:
Qty:
Part #:305684
- 2" Conduit Size Standard Round Knockout Punch
Knurled edge for better grip
Laser markings for quick part identification
Made in USA
Replaces 441AV
Qty:
Part #:305674
- Round Conduit Die - 2"
Made in the USA
Replacement Die 2" Conduit Size, 2-3/8" (61.5 mm) Actual Hole Size for Standard Round Knockout Punches
Alignment Markings improve punching accuracy and productivity when making holes.
Punches and dies are marked with catalog numbers and sizes for quick part identification.
Qty:
Part #:504373
- 1" Drive 6-Point SAE 1-1/8" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:503791
- 4700 Series 2" Putty Knife
The 4700 Promotional Series of quality plastic putty knives, scrapers and adhesive scrapers. Ideal for most home repair projects.
$
0.75
Qty:
Part #:811364
- 1/2" Drive 2" Extension
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
&bull Spinner disk is ideal for fast turn down of fasteners
Qty:
Part #:811412
- 1/4" Drive 2" Extension
&bull All tools are professional quality, made of high-grade chrome vanadium steel
&bull Sockets feature SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Packed in rugged compact high-density polyethylene (HDPE) cases that are strong and durable yet light in weight
Qty:
Part #:509575
- 1-1/8" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:513144
- 23 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
nch 12-Point, Metric
Qty:
Part #:500491
- 3/4" Drive Shallow Sockets, 12-Point, SAE, High Polished Chrome Finish
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
closeout
$45.15 MSRP
$
28.04
Part #:505780
- CLOSEOUTS Only 2 Left!
- Hard Soft-Face Hammer Tip 2" &bull Heavy-duty construction for strength and durability
Qty:
closeout
$26.85 MSRP
$
16.67
Part #:506465
- CLOSEOUTS Only 4 Left!
- Medium Soft-Face Hammer Tip 2" &bull Heavy-duty construction for strength and durability
Qty:
Part #:811947
- Soft Soft-Face Hammer Tip 2"
Heavy-duty construction for strength and durability
Qty:
closeout
$45.15 MSRP
$
28.04
Part #:811952
- CLOSEOUTS Only 6 Left!
- Extra Hard Soft-Face Hammer Tip 2" &bull Heavy-duty construction for strength and durability
Qty:
Part #:811953
- Tough Soft-Face Hammer Tip 2 "
Heavy-duty construction for strength and durability
Qty:
Part #:509572
- 1-1/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:812980
- 8" Cold Chisels 1 1/8"
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:507835
- 1/2" Drive SAE 1-1/8" Impact Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for maximum engagement on 6 point fasteners
&bull Suitable for use with pneumatic and electric impact wrenches
&bull Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Displaying: 25 - 48 of 74 Matching Items