1-7/16in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Length: 1-7/16in 7-1/2in 11-1/2in
Qty:
Part #:811447
- 3/8" Drive Round Head Ratchet 7-5/8"
&bull Double pawl design with 72 teeth action provides a 5° ratcheting angle
&bull Shift lever reverses action instantly
&bull Knurled handle provides a non-slip grip
&bull Chrome finish models provides increased protection from rust and corrosion
Qty:
Part #:810247
- 7 1/2" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:503695
- 1-1/4" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Part #:500317
- 2 to 4-3/4" SAE Adjustable Hook Spanner Wrench
&bull Ideal for adjusting collars, lock nut rings, and bearings
&bull Specifically engineered to hold up under the most rigorous industrial use
Qty:
Part #:505666
- 1-7/16" 12-Point SAE Offset Pattern Box End Striking Wrench
Striking face wrenches are designed to be struck by a hammer on the anvil area in order to loosen frozen fasteners or to set and tighten fasteners
Anvils are proportional to opening sizes. Special heat treating provides maximum durability for long life
Offset handle is close to head to provide clearance in confined areas
Williams' expanded line of offset striking face wrenches, up to 4-1/4", provides the most extensive line on the market
Specifically engineered to hold up under the most rigorous industrial use
Qty:
Qty:
Qty:
Qty:
Part #:811413
- 1/4" Drive Adapter 1-7/16"
All tools are professional quality, made of high-grade chrome vanadium steel
Sockets feature SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Packed in rugged compact high-density polyethylene (HDPE) cases that are strong and durable yet light in weight
Qty:
Part #:513141
- 20 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
Qty:
Part #:812975
- 7 1/2" Chain Nose Pliers
&bull Polished heads resist rust and corrosion, extending the tool life
&bull Diamond serrated jaws with industrial hardened cutting edges
Qty:
Part #:509572
- 1-1/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Displaying: 1 - 14 of 14 Matching Items