1-7/8in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Size: 1-7/8in 1/8in 3/16in 7/16in
Part #:502912
-
3/16&rdquo Cold Shut, Steel, Zinc Plated
Connections for Chain and Attachments
When Using Cold Shuts with Chain, Use One Size Larger Than Chain Size
With A Hammer, Drive the Open End Through the Cold Shut Eye. Peen the Extended End to Prevent Opening
Order Unit is "Each"
Note Cold Shuts Should Not Be Reused After Closure Has Been Made
DO NOT EXCEED THE WORKING LOAD LIMIT
Do Not Use for Overhead Lifting or Hoisting
Qty:
Part #:504832
- Hex End L-Wrenches - ProGuard&trade Finish
Chamfered tool tips eliminate burrs and help tools seat in screw head
Sharp corners transfer more torque to the screw and reduce stripping
Precision machined for ease of use and superior fit
Qty:
Part #:511841
- 3/16" Wire Rope Clip, Electro-Galvanized
If Used on Coated Cable, Remove the Coating From the Assembly Area
Follow Assembly Instructions
Qty:
Qty:
Part #:511840
- 1/8" Wire Rope Clip, Electro-Galvanized
If Used on Coated Cable, Remove the Coating From the Assembly Area
Follow Assembly Instructions
Qty:
Part #:504830
- Hex End L-Wrenches - ProGuard&trade Finish
Chamfered tool tips eliminate burrs and help tools seat in screw head
Sharp corners transfer more torque to the screw and reduce stripping
Precision machined for ease of use and superior fit
Qty:
Part #:511937
-
3/16" Wire Rope Thimble, Electro-Galvanized
If Used on Coated Cable, Remove the Coating From the Assembly Area
Follow Assembly Instructions
Qty:
Part #:508012
-
3/16" Grade 30 Proof Coil Chain, Zinc Plated, 250' per Round Pail
Excellent Low Carbon Steel Chain for General Purpose Applications
Frequently Used for Fabricating Tow Chains, Binding and Logging Chains, Marine and Other General Applications
Standard Finish Zinc Plated or Galvanized
Hallmarking "C3" and "USA" on 5/16" and Larger
Proof Tested
Design Factor 4 to 1
Packaged in Pails, Order Unit is "Each"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:459-10907
- Bondhus® Balldriver® L-Wrench KeysProduct DetailsBall end inserts into a screw at a 25° angle and allows natural hand and wrist movementSaves time by quickly funneling tool into screwSuperior ball end strength and working angleWorks in hard-to-reach places.
Qty:
Part #:508146
- 3/16-Inch Cabinet Tip Screwdriver 4-Inch
&bull Narrow cabinet tip permits blade access where space is limited&bull Cushion-Grip handle for greater torque and comfort&bull Premium chrome-plated for smooth feel and corrosion resistance&bull Internal flanges inside handle provide solid, twist-resistant blade anchor&bull Special heat-treated shafts&bull Precision-machined tip for exact fit&bull Tip-Ident® quickly identifies the screwdriver type and tip orientation&bull Meets or exceeds applicable ASME / ANSI specifications
Qty:
Qty:
Part #:502805
-
3/16" Grade 30 Proof Coil Chain, Zinc Plated, 250' per Round Pail
Excellent Low Carbon Steel Chain for General Purpose Applications
Frequently Used for Fabricating Tow Chains, Binding and Logging Chains, Marine and Other General Applications
Standard Finish Zinc Plated or Galvanized
Hallmarking "C3" and "USA" on 5/16" and Larger
Proof Tested
Design Factor 4 to 1
Packaged in Pails, Order Unit is "Each"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:500504
- 3/4" Drive 12-Point SAE 1-7/8" Shallow Socket
&bull SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Designed for quick engagement on both 6 and 12 point fasteners
Qty:
Part #:501590
- 1/2" Drive SAE 5/8" Long Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Qty:
Qty:
Part #:503701
- Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
closeout
$12.46 MSRP
$
7.11
Part #:511845
- CLOSEOUTS Only 5 Left!
-
7/16" Wire Rope Clip, Forged Carbon Steel, Galvanized (Being replaced by Columbus Mckinnon 2/Pack 490-M249-2)
Base is Drop-Forged Carbon Steel
Hot Galvanized to ASTM A-153 to Resist Rust and Corrosion
U-Bolts Are colored Blue for Identification Purposes and Use Heavy Duty Hex Nuts (UNC-2A)
Designed to Meet Federal Specifications, FF-C-450, Type 1, Class 1
Designed to Meet or Exceed All Requirements of ASME B30.26 Including Identification, Ductility, Design Factor and Temperature
Permanently Marked with Size and Manufacturer
Sizes 1/4" and Above Marked with USA and Date Code
Sizes 1/8" Through 1-1/4" Are Supplied Bagged and Unassembled
Note See Application and Warning Information
Qty:
Part #:810310
- 10" Long Taper Punches
Designed for aligning the holes in metal pieces through which rivets, bolts, or screws will be inserted
Not intended for driving pins as punch may become stuck in work
Also called line-up aligning or drift punches
Qty:
Part #:810266
- 4 3/4" Pin Punches
For driving out and removing already loosened pins and keys after initial movement by a solid or starter punch
Qty:
Part #:500171
- 3/8" Drive Standard Length Hex Bit Sockets, SAE, High-Polioshed Chrome Finish
&bull All tools are professional quality, made of high-grade chrome vanadium steel
&bull Sockets feature SUPERTORQUE® lobular openings for greater turning power without deforming the fastener
&bull Metal tool box made for years of rugged use
Qty:
Part #:507925
- 1/4" Drive 6-Point SAE 7/16" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Qty:
Part #:504200
- 1" Drive 6-Point SAE 1-7/8" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:805457
- Pipe Dies for Machine Die Heads
Qty:
Displaying: 1 - 24 of 109 Matching Items