4-3/4"
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Alt. Length: 4-3/4" 11-1/2" 22"
Part #:503703
- 5/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:810266
- 4 3/4" Pin Punches
For driving out and removing already loosened pins and keys after initial movement by a solid or starter punch
Qty:
Qty:
Part #:500317
- 2 to 4-3/4" SAE Adjustable Hook Spanner Wrench
&bull Ideal for adjusting collars, lock nut rings, and bearings
&bull Specifically engineered to hold up under the most rigorous industrial use
Qty:
Part #:505666
- 1-7/16" 12-Point SAE Offset Pattern Box End Striking Wrench
Striking face wrenches are designed to be struck by a hammer on the anvil area in order to loosen frozen fasteners or to set and tighten fasteners
Anvils are proportional to opening sizes. Special heat treating provides maximum durability for long life
Offset handle is close to head to provide clearance in confined areas
Williams' expanded line of offset striking face wrenches, up to 4-1/4", provides the most extensive line on the market
Specifically engineered to hold up under the most rigorous industrial use
Qty:
Part #:513141
- 20 mm 12-Point Metric SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
Qty:
Part #:1184-JHW8910
- 1-5/8" SAE Offset Structural Box Wrench
&bull Offset from handle to permit clearance of obstructions
&bull Handles are tapered for insertion into bolt holes
&bull Industrial Black Finish
Qty:
Part #:729-48-20-4052
- Business Unit Accessories. Product Level 1 Accessories MAS-CON. Product Level 2 Accessories Drilling. Product Level 3 ACCY Masonry. Product Level 4 ACCY Spline 2 Cutter Bits. Product Level 5 ACCY Blank. AX Item Number 48204052. Country of Origin DEU. Harmonized Tariff 8207502030.:
Qty:
Part #:729-48-20-4088
- Business Unit Accessories. Product Level 1 Accessories MAS-CON. Product Level 2 Accessories Drilling. Product Level 3 ACCY Masonry. Product Level 4 ACCY Spline 2 Cutter Bits. Product Level 5 ACCY Blank. AX Item Number 48204088. Country of Origin DEU. Harmonized Tariff 8207502030.:
Qty:
Displaying: 1 - 9 of 9 Matching Items