2-1/16in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Length: 2-1/16in 5-1/4in 7-1/2in 100ft
Part #:500566
- #2 Twist Link Machine Chain, Zinc Plated, 100' per Carton
Uses General Utility Applications
Standard Material Low Carbon Steel
Standard Finish Bright, Zinc Plated and Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Qty:
Qty:
Qty:
Part #:502824
-
2/0 Double Loop (Inco) Chain, Zinc Plated, 100' per Carton
Farm and Animal Chains, and Many General-Purpose Applications
Standard Material Low Carbon Steel
Standard Finish Zinc Plated, Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Note Avoid Twisting in Suspension Applications
Campbell Recommends The Use of Proof Coil or Straight Link Coil Chain for Swing Set Applications
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:502825
-
1/0 Double Loop (Inco) Chain, Zinc Plated, 100' per Reel
Farm and Animal Chains, and Many General-Purpose Applications
Standard Material Low Carbon Steel
Standard Finish Zinc Plated, Polycoated in White, Yellow, Green or Red Colors
Design Factor 4 to 1
Packaged on Reels, Order Unit is "Each"
Made in the USA
Note Avoid Twisting in Suspension Applications
Campbell Recommends The Use of Proof Coil or Straight Link Coil Chain for Swing Set Applications
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:503695
- 1-1/4" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:810247
- 7 1/2" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:811447
- 3/8" Drive Round Head Ratchet 7-5/8"
&bull Double pawl design with 72 teeth action provides a 5° ratcheting angle
&bull Shift lever reverses action instantly
&bull Knurled handle provides a non-slip grip
&bull Chrome finish models provides increased protection from rust and corrosion
Qty:
Part #:500763
- 3/8" x 100' Banner® Yellow Clad Tape Measure
The Crescent Banner Tape Measure has a rugged, vinyl-covered steel case. Its large easy action winding drum and nylon rollers prevent friction for a easy rewind. The tape has a 2-in-1 endhook that allows users to grasp on to what ever is available.
Qty:
Part #:509622
- 100' Nylon Fishtape
Non-conductive, curl resistant nylon tape for fast, clean fishing
Good for fishing in conduit with wire or cable present
Rugged case design improves drop impact capability
Advanced comfort handle grip reduces fatigue
Nylon fish tape is intended for fishing only
Rope or line is recommended for pulling
Qty:
Part #:500934
- 100' REEL-X Non-Conductive Fish Tape
Free-spinning interior reel for faster fishing
Utilize secondary exit and set case on the ground to free-up both hands for fishing
Anti-Bind Design
Quick-Change replacement reels
Fatigue/Strain reducing ergonomic case design
Bulk Pack Available (Qty 3) - FTXF-100BP
Compatible Replacement Reels RFTXF-50, RFTXF-100
Qty:
Part #:917-62605
- ONE-PIECE FLAT SEWER TAPE&bull Sizes and lengths for use on sewer and drain lines through 8" (200 mm) in diameter and up to 100'(30,4 m) in length.&bull Carrier included with all except 25' (7,6 m) model.&bull All models have a hand grip and a spear point at one end and roller ball at the othe
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:501654
-
1/0 Straight Link Machine Chain, Zinc Plated, 100' per Carton
Uses General Utility, Animal, and Farm and Ranch Applications
Standard Material Low Carbon Steel
Standard Finish Bright and Zinc Plated
Proof Tested
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:804793
-
#10 Single Steel Jack Chain, Zinc Plated, 100' per Carton
Fixture and Novelty Suspension
General Utility Use Not Requiring High Strength
Standard Material Low Carbon Steel
Standard Finish Zinc Plated
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Qty:
Qty:
Part #:503092
-
1/0 Twist Link Machine Chain, Zinc Plated, 100' per Carton
Uses General Utility Applications
Standard Material Low Carbon Steel
Standard Finish Bright, Zinc Plated and Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:502826
- #1 Double Loop (Inco) Chain, Zinc Plated, 100' per Carton
Farm and Animal Chains, and Many General-Purpose Applications
Standard Material Low Carbon Steel
Standard Finish Zinc Plated, Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Note Avoid Twisting in Suspension Applications
Campbell Recommends The Use of Proof Coil or Straight Link Coil Chain for Swing Set Applications
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Displaying: 1 - 24 of 36 Matching Items