2-1/2in
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Length: 2-1/2in 4-3/4in 24in 100ft
Part #:500566
- #2 Twist Link Machine Chain, Zinc Plated, 100' per Carton
Uses General Utility Applications
Standard Material Low Carbon Steel
Standard Finish Bright, Zinc Plated and Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Qty:
Part #:505976
- 1/2" x 100' Linear Fiberglass Tape Measure
The Crescent Linear Fiberglass Tape Measure has a lightweight, high impact ABS case. Its non-conductive fiberglass blade is great for any jobsite. The blade has easy to read black and red markings on a yellow background. Its endhook folds to prevent it from catching in a toolbox, increasing the longevity of the tape.
Qty:
Qty:
Part #:502824
-
2/0 Double Loop (Inco) Chain, Zinc Plated, 100' per Carton
Farm and Animal Chains, and Many General-Purpose Applications
Standard Material Low Carbon Steel
Standard Finish Zinc Plated, Galvanized
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Note Avoid Twisting in Suspension Applications
Campbell Recommends The Use of Proof Coil or Straight Link Coil Chain for Swing Set Applications
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:841-329-86996
- Extra Large Kneeling Pad
The GEARWRENCH® Kneeling Pad is the super convenient way to keep your knees comfortably off of a hard or rough floor. A built in grab handle makes it easy to position or hang up when not in use. Three layers of high-density solvent resistant foam provide an unmatched degree of cushioning so you can get the job done in comfort. A magnetized recess holds nuts, bolts, and spare parts.
Qty:
Qty:
Qty:
Part #:503703
- 5/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:502825
-
1/0 Double Loop (Inco) Chain, Zinc Plated, 100' per Reel
Farm and Animal Chains, and Many General-Purpose Applications
Standard Material Low Carbon Steel
Standard Finish Zinc Plated, Polycoated in White, Yellow, Green or Red Colors
Design Factor 4 to 1
Packaged on Reels, Order Unit is "Each"
Made in the USA
Note Avoid Twisting in Suspension Applications
Campbell Recommends The Use of Proof Coil or Straight Link Coil Chain for Swing Set Applications
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:810266
- 4 3/4" Pin Punches
For driving out and removing already loosened pins and keys after initial movement by a solid or starter punch
Qty:
Part #:504074
- 3/4" Drive Adapter 3/4" Female x 1/2" Male 2-1/2"
Specially heat treated for impact use to provide long life, safety, and durability
Pin and o-ring or RET RING (sold separately) secure tools onto impact wrench for safety and convenience
Suitable for use with pneumatic and electric impact wrenches
Drive end features pin retention hole and groove
Qty:
Part #:807747
- 3/4" Drive SAE 1-1/8" Impact Shallow Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6 point fasteners
Suitable for use with pneumatic and electric impact wrenches
Specially heat treated for impact use to provide long life, safety, and durability
Qty:
Part #:500763
- 3/8" x 100' Banner® Yellow Clad Tape Measure
The Crescent Banner Tape Measure has a rugged, vinyl-covered steel case. Its large easy action winding drum and nylon rollers prevent friction for a easy rewind. The tape has a 2-in-1 endhook that allows users to grasp on to what ever is available.
Qty:
Qty:
Part #:509622
- 100' Nylon Fishtape
Non-conductive, curl resistant nylon tape for fast, clean fishing
Good for fishing in conduit with wire or cable present
Rugged case design improves drop impact capability
Advanced comfort handle grip reduces fatigue
Nylon fish tape is intended for fishing only
Rope or line is recommended for pulling
Qty:
Part #:500934
- 100' REEL-X Non-Conductive Fish Tape
Free-spinning interior reel for faster fishing
Utilize secondary exit and set case on the ground to free-up both hands for fishing
Anti-Bind Design
Quick-Change replacement reels
Fatigue/Strain reducing ergonomic case design
Bulk Pack Available (Qty 3) - FTXF-100BP
Compatible Replacement Reels RFTXF-50, RFTXF-100
Qty:
Part #:917-62605
- ONE-PIECE FLAT SEWER TAPE&bull Sizes and lengths for use on sewer and drain lines through 8" (200 mm) in diameter and up to 100'(30,4 m) in length.&bull Carrier included with all except 25' (7,6 m) model.&bull All models have a hand grip and a spear point at one end and roller ball at the othe
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:501654
-
1/0 Straight Link Machine Chain, Zinc Plated, 100' per Carton
Uses General Utility, Animal, and Farm and Ranch Applications
Standard Material Low Carbon Steel
Standard Finish Bright and Zinc Plated
Proof Tested
Design Factor 4 to 1
Packaged in Cartons, Order Unit is "Feet"
Made in the USA
Do Not Use for Overhead Lifting
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Displaying: 1 - 24 of 39 Matching Items